InFocus IN2102 User Manual

14
Shutting down the projector
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or
keypad button is pressed.
Screen Save Time
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save Time feature in the Setup menu. See page 30.
Auto Off Time
The projector also has a Auto Off Time feature that automatically turns the
lamp off after no active sources are detected and no user interaction with
the projector is performed for 30 minutes. By default, this feature is off. You
can change the length of time, see
page 30.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad.
The lamp turns off and the LED blinks amber for 1 minute while the fans
continue to run to cool the lamp. When the lamp has cooled, the LED lights
amber and the fans stop. Unplug the power cable to completely power off
the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
Table 2: Status indicator light behavior and meaning
Status Indicator Panel icons Meaning
Power, solid amber
Power, blinking green
Power, solid green
Power, blinking amber
The projector is plugged in.
The power button has been pressed and
the software is initializing.
The projector is on and initialized.
The power button has been pressed to
turn the projector off and the fans are
running to cool the projector.
Thermometer The projector is too hot. Make sure the
vents aren’t blocked (see
page 20). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists
.
Lamp Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/service
to contact Service.

InFocus IN2102 Specifications

General

Matrix size	0.55 \
Projection distance	10 m
Vertical scan range	50 - 85 Hz
Horizontal scan range	31 - 79 kHz
Projection technology	DLP
Contrast ratio (typical)	2000:1
Projector native resolution	SVGA (800x600)
Keystone correction, vertical	-20 - 20 °
Aspect ratio	4:3, 5:4, 16:9
RS-232 ports	1
Dimensions (WxDxH)	297.2 x 228.6 x 99.1 mm
Power requirements	100 - 240, 50 - 60 Hz
Connectivity technology	Wired
Lamp power	200 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	3000 h
Analog signal format system	NTSC, PAL, SECAM
RMS rated power	2 W
Microphone in	Yes
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Component video (YPbPr/YCbCr) in	2
Noise level	35 dB
Certification	UL, c-UL, FCC-A, CE, GOST, TUV GS, CCC, IRAM, NOM, C-Tick, MIC, eK, PSB
Power consumption (typical)	250 W
Operating temperature (T-T)	5 - 31.11 °C

Weight and Dimensions

Weight	3130 g
Package weight	5260 g