Integra DTR-70.3 User Manual

51
En
■ Subwoofer Phase
` 0
º
` 180º:
Moves the subwoofer phase.
Note
•If the “Subwoofer” setting is set to “No”, this setting cannot be
selected.
■ Wireless Subwoofer
` Yes:
The audio is output from the speakers connected to
the wireless unit.
` No
:
The audio is not output from the speakers connected
to the wireless unit.
When the wireless unit is connected to the UNIVERSAL
PORT jack on the AV receiver, you can select if you wish
to output the audio from the speakers connected to the
wireless unit.
Note
•If the “Subwoofer” setting is set to “No”, this setting cannot be
selected (➔ page 50).
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
■ Unit
` feet:
Distances can be set in feet. Range: 0.2ft to 30.0ft in
0.2 foot steps.
` meters:
Distances can be set in meters. Range: 0.06m to
9.00m in 0.06 meter steps.
(The default setting varies from country to country.)
■ Left, Front Wide Left, Front High Left, Center,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right,
Surround Back Left, Surround Left,
Subwoofer 1, Subwoofer 2
*1
` Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to “No” or “None” in the
“Speaker Configuration” cannot be selected (➔ page 50).
*1
If the “Subwoofer” setting is set to “1ch”, this setting cannot
be selected (➔ page 50).
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■ Left, Front Wide Left, Front High Left, Center
*1
,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right,
Surround Back Left, Surround Left
` –12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■ Subwoofer 1
*1
, Subwoofer 2
*1*2
` –15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
Note
• These settings cannot be calibrated when the AV receiver is
muted.
• Speakers that you set to “No” or “None” in the
“Speaker Configuration” cannot be selected (➔ page 50).
• The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at
volume settings below this, be careful because the test tone will
be much louder.
*1
For the center speaker and subwoofer, the level settings made
by using the Home menu are saved in this menu
(➔ page 41).
*2
If the “Subwoofer” setting is set to “1ch”, this setting cannot
be selected (➔ page 50).
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
speaker setting menu may appear on screen.
This setting is set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function (➔ page 31).
This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function (➔ page 31).

Integra DTR-70.3 Specifications

General

Brand	Integra
Model	DTR-70.3
Category	Receiver
Language	English