Copyright © Itech Electronic Co., Ltd.
IX
IT6000B Series User Manual
4.6.3 Built-in Waveform Function ......................................................................... 75
4.6.4 Solar Photovoltaic Curve Simulation Function (SAS) ............................... 108
4.6.5 Battery Simulation Function ...................................................................... 112
5 Load Function................................................................................................................. 118
5.1 Programming the Input ........................................................................................ 118
5.1.1 Select the Operation Mode (Mode) ........................................................... 118
5.1.2 Basic Operation Mode ............................................................................... 119
5.1.3 Complex Operation Mode ......................................................................... 120
5.1.4 Set the Input-On/Input-Off Delay Time （On Delay/ Off Delay） ............. 122
5.1.5 Set I-Rise / I-Fall Slope（I-Rise / I-Fall Slope）........................................ 122
5.1.6 Set V-Rise / V-Fall Slope（V-Rise / V-Fall Slope）.................................. 123
5.1.7 Set P-Rise / P-Fall Slope（P-Rise / P-Fall Slope）.................................. 123
5.1.8 Short-Circuit Analog Function ................................................................... 123
5.1.9 VON Function（Von） .............................................................................. 123
5.2 Advanced Feature................................................................................................ 125
5.2.1 LIST Function ............................................................................................ 125
5.2.2 Battery Discharging Test Function ............................................................ 131
5.3 Protection Function .............................................................................................. 132
5.3.1 Set Over-Current Protection (OCP)........................................................... 134
5.3.2 Set Over-Power Protection (OPP)............................................................. 135
5.3.3 Set Under-Voltage Protection (UVP)......................................................... 135
5.3.4 Over-Temperature Protection (OTP)......................................................... 136
5.3.5 Sense Reverse Protection......................................................................... 137
6 Basic Operation.............................................................................................................. 138
6.1 Local/Remote Mode Switch ................................................................................. 138
6.2 Key Lock Function ............................................................................................... 139
6.3 Save and Recall Operations ................................................................................ 139
6.3.1 Save Operation.......................................................................................... 140
6.3.2 Recall Operation........................................................................................ 141
6.4 Data Logging Function......................................................................................... 141
6.5 Set the Beeper Status (Beep) .............................................................................. 144
6.6 Set the Power-on State (PowerOn) ..................................................................... 144
6.7 Sense Function (Sense) ...................................................................................... 147
6.8 Select Trigger Source (Trig Source) .................................................................... 148
6.9 Set the Communication Information (I/O Con) .................................................... 149
6.10 Set Parallel Operation Mode (Parallel) .............................................................. 149
6.11 Digital I/O Function (Digital Port) ....................................................................... 153
6.11.1 IO–1. Ps-Clear, Not-Invert....................................................................... 156
6.11.2 IO–2. Ps, Not-Invert................................................................................. 158
6.11.3 IO–3. Off-Status, Not-Invert..................................................................... 160
6.11.4 IO–4. Ext-Trig, Not-Invert ........................................................................ 162
6.11.5 IO–5. INH-Living, Not-Invert .................................................................... 165
6.11.6 IO–6. Sync-On, Not-Invert....................................................................... 168
6.11.7 IO–7. Sync-Off, Not-Invert....................................................................... 170
6.12 Source Analogue Function (Ext-Program) (Optional) ....................................... 172
6.13 loadAnalogue Function (Ext-Program) (Optional) ............................................. 177
6.14 Restored to Factory Setting (System Reset) ..................................................... 182
6.15 View the System Information (System Info) ...................................................... 187
6.16 Observe Power Grid Information (AC-Meter) .................................................... 188
6.17 Display Loading Time (Disp on timer)................................................................ 189
6.18 System Upgrade ................................................................................................ 189
7 Technical Specification .................................................................................................. 193
7.1 Main Specification................................................................................................ 193
7.1.1 IT6006C-500-30 ........................................................................................ 194
7.1.2 IT6012B-500-60......................................................................................... 198
7.1.3 IT6018B-500-90......................................................................................... 202
7.1.4 IT6006B-800-20......................................................................................... 206
7.1.5 IT6018B-800-60......................................................................................... 210
To Next Page
Loading...
Need help?
General
