What to do if my Jackson DishStar LT doesn’t drain when the power button is pressed?
If your Jackson Dishwasher isn’t draining when you press the power button, the issue could be due to: * A clogged drain. Remove any obstructions to clear it. * A defective drain valve. In this case, the valve will need to be replaced.
What to do if no water comes through the arms when the "WASH/DELIME" switch is pressed on my Jackson DishStar LT?
If no water is coming through the arms when you press the "WASH/DELIME" switch on your Jackson Dishwasher, it could be because: * The water is not turned on. Make sure to turn the water on. * A defective solenoid valve. Replace the solenoid valve.
How to stop water overflow from the bottom of the Jackson DishStar LT Dishwasher door?
If water is overflowing from the bottom of your Jackson Dishwasher's door, here are a few things to check: * A clogged drain may be the culprit; remove any obstructions. * Ensure the machine is level, adjusting its height if necessary. * Excessive inlet pressure can cause overflow; install or adjust a pressure regulator, ensuring flow meets the data plate specifications. * Too much detergent can lead to foaming; reduce the quantity you're using. * A missing wash/rinse arm end-cap can also cause this issue; replace it if it's missing.
Why is the wash temperature not at the required range in my Jackson DishStar LT Dishwasher?
If the wash temperature of your Jackson Dishwasher is not at the required range, consider the following possible causes: 1. Low water level. Check the water level and run a new fill cycle if it's low. 2. RTD setpoint too slow. Check the fault screen and adjust the wash temperature setpoint. 3. Defective RTD. Replace the RTD. 4. Defective wash heater. Replace the heater element. 5. Defective heater contactor R1. Replace it.
Why is there little or no water coming through the wash/rinse assemblies of my Jackson Dishwasher?
If you're experiencing little to no water coming through the wash/rinse assemblies of your Jackson Dishwasher, it could be due to: * Limed-up heads or piping. Delime the heads to resolve this. * Low water pressure. Adjust the pressure regulator (not supplied) or increase the pipe size to the machine.
Why is rinse water not at the required temperature range in my Jackson DishStar LT?
If the rinse water in your Jackson Dishwasher isn't reaching the required temperature range, consider these potential reasons: * Incoming rinse water not meeting the minimum criteria indicated on the machine data plate. Adjust as required. * A defective RTD. Replace it if necessary. * Damaged rinse heaters. Check amperages and replace if necessary. * Setpoint screens set too low. Adjust the rinse tank setpoint.
Why doesn’t the wash motor operate on delime wash in my Jackson DishStar LT Dishwasher?
If the wash motor isn’t operating during the delime wash cycle on your Jackson Dishwasher, the possible causes include: * Loose or broken wires. Reconnect or replace the wires in the motor. * A defective "WASH/DELIME" switch. Verify the switch triggers input on the PLC. If not, check the wiring or replace the membrane. * A defective motor starting relay. Replace the relay. * The machine is in FAULT mode and locked out. Review the fault screen for active faults.
What to do if rinse water runs continuously in my Jackson DishStar LT even with the breaker turned off?
If the rinse water runs continuously in your Jackson Dishwasher even after the breaker is turned off, it could be due to: * A defective plunger in the solenoid valve. Replace the plunger. * A defective diaphragm in the solenoid valve. Replace the diaphragm.
Why is there no indication of pressure in my Jackson DishStar LT?
If there is no pressure indication in your Jackson Dishwasher, it could be due to: * Water being turned off. Turn the water on. * Pressure gauge failure. Replace the pressure gauge.
Covers repair or replacement of defective parts within one year from installation.
Outlines voltage, phase, frequency, and load requirements.
Procedure for loading and starting a wash cycle.
Adjusting various temperature and time setpoints on HT models.
Lists fault codes, their causes, and remedies for HT models.
Addressing common issues like water overflow, motor failure, or temperature problems.
Electrical schematic for the DishStar HT model.
General| Racks per Hour | 24 |
|---|---|
| Wash Temperature | 150 °F |
| Final Rinse Temperature | 180 °F |
| Voltage | 115V |
| Type | Undercounter |
| Dimensions | 33.31" x 24.19" x 25.25" |
To Next Page
