To Next PageTo Next PageWhat to do if the Jackson Dishwasher doesn’t drain when the “OFF/DRAIN” switch is pressed?
If your dishwasher isn't draining, start by removing any obstructions that might be blocking the drain. If that doesn't work, consider replacing the part.
How to fix water overflow from the bottom of the Jackson Avenger LT door?
If you're experiencing water overflow, try these solutions: First, remove any obstructions that may be causing the overflow. Next, ensure the machine is level, and if not, increase the height to the front. If the issue persists, install a pressure reducing valve, or adjust the existing one to ensure the flow is 20 ±5 PSI. Finally, try reducing the amount of detergent you're using.
What to do if the wash temperature is not at the required reading on the Jackson Avenger LT Dishwasher?
If the wash temperature isn't reaching the required level, try the following: First, ensure the water is turned on. You can also try to adjust or replace the thermostat, or replace the heater element and pressure gauge. Note that there is additional information on page 12. Finally, consider replacing the part.
Why is there little or no water coming through the rinse assemblies of my Jackson Avenger LT?
If you're experiencing low water flow through the rinse assemblies, try deliming the rinse heads. Additionally, you might need to increase the pipe size to the machine and adjust the pressure regulator.
What to do if the Jackson Avenger LT rinse water is not at the required temperature range?
If the rinse water temperature is not within the required range, see the note in the installation instructions. You can also try adjusting the thermostat, replacing it if necessary, or making other necessary adjustments.
Why does the Jackson Avenger LT Dishwasher rinse water run continuously even with the breaker turned off?
If the rinse water continues to run even after the breaker is turned off, consider replacing the part or the diaphragm.
What to do if no water comes through the rinse arms when the “ON/FILL” switch is depressed on Jackson Dishwasher?
If no water is coming through the rinse arms, first ensure that the water is turned on. If the problem persists, consider replacing the solenoid valve.
What to do if the wash motor doesn’t operate on manual wash in Jackson Dishwasher?
If the wash motor isn’t working on manual wash, try reconnecting or replacing the wires in the motor. If that doesn't solve the problem, consider replacing the motor.
What to do if the motor operates on manual wash but not on automatic in Jackson Dishwasher?
If the motor works in manual mode but not automatically, replace the switch.
What to do if there is no indication of pressure in Jackson Avenger LT Dishwasher?
If there is no pressure indication, first ensure that the water is turned on. If the issue persists, replace the pressure gauge.
General| Brand | Jackson |
|---|---|
| Model | Avenger LT |
| Category | Dishwasher |
| Language | English |
Details operating capacity, cycle times, temperatures, and water requirements.
Provides dimensional data and connection points for the Avenger HT model.
Provides dimensional data and connection points for the Avenger LT model.
Guides on checking for damage, unpacking, and identifying missing parts.
Covers water supply connections, hardness considerations, and plumbing codes.
Details electrical power connection procedures, voltage checks, and safety.
Instructions for setting up, priming, and managing chemical feeder pumps.
Step-by-step guide for daily startup, washing, and cleaning procedures.
Procedures for removing lime and corrosion deposits from the dishmachine.
Outlines routine checks, cleaning, and operator responsibilities for maintenance.
Addresses water overflow from the door and problems with the wash motor operation.
Covers problems with water supply, rinse temperature, and draining functions.
Details components and diagrams for control panel weldment assemblies for HT and LT models.
Exploded views and part numbers for chemical feeder pump assemblies.
Diagrams and part lists for water and vacuum plumbing for Avenger HT models.
Illustrates and lists components of the motor and pump assembly.
Details parts and diagrams for the dishmachine door and its related components.
Wiring diagram for the Avenger HT model with 208-230V single-phase power.
Wiring diagram for the Avenger HT model with 480V three-phase power.
Wiring diagram for the Avenger LT model with 115V single-phase power.
Lists authorized service centers located in Alabama.
Lists authorized service centers located in California.
Lists authorized service centers located in Florida.
Lists authorized service centers located in Illinois.
Lists authorized service centers located in New York.
Lists authorized service centers located in Texas.
Lists authorized service centers located in Wisconsin.
