JVC CA-S200 - Tuning in a Station; Eseeeseeeeeee Eiescetalysacbaass; Presetting Stations.0; Receiving in Stereo or MOM0

Tuning in a Station
Press
AM
or
FM
to
turn
on
the
radio.
The
display
shows
the
station
frequency
tuned
to.
<
AL Three ways to select a station
o
*
Press
TUNING
<
or
>
repeatedly
to
move
from
frequency
to
frequency
until
you
find
the
Afr Three ways to tune one you want:
in a station * Holddown TUNING < or >, the frequency starts changing on the display. When a station
is tuned in, “TUNED” lights up on the display and the frequency stops changing.
*
Press
once
and
release
PRESET
<
or
>
to
go
to
the
next
preset
station,
or
hold
PRESET
<
or
>
to
cycle
through
the
preset
stations:
release
the
button
when
the
preset
station
you
want
shows
on
the
display.
(This
method
is
possible
only
after
presetting
stations.)
You can also use the Remote to tune in stations and preset channels:
To tune preselected stations with the Remote:
1. Press TUNER to select the band you want.
2.
Select
the
station
by
entering
the
presvt
channel
number
in
the
10
key pad
of
the
Remote
(Refer
to
page
19).
Presetting Stations
How
to
preset
Once
a
station
is
assigned
to
a
channel
number,
the
station
can
be
quickly
tuned
either
from
the
AM
and
FM
radio
Remote
using
the
10
key
pad
of
the
Remote
or
the
CA-S200
itself
using
PRESET
<
or
>
to
call
stations
up
the channel
number.
néuR kung Q) You can preset 40 AM and FM stations at random.
1.
5S Preset stations may be erased when power is cut off to the Unit, as when it is
<=
TUNING
>
unplugged
from
the
AC
outlet
or
a
power
failure
occurs.
If
the
preset
stations
are
lost,
simply
set
the
stations
again
using
the
following
procedure.
SOURCE/REC TIME To preset radio stations
1. Tune in the station you want to set using TUNING <r >.
2. Press MEMORY.
On the display “MEMORY” will blink for 4 seconds.
©
During
these
4
seconds
while
“MEMORY”
is
blinking
assign
a
channel
number
to
the
station
and
enter
it
into
the
memory.
3.
Select
a
channel
number
by
pressing
PRESET
<<
or
>
until
you
find
the
channel
number
you
want.
4.
Press
MEMORY
and
the
station
will
be
assigned
to
the
channel
number
shown
on
the
SOURCE/REC
TIME
display.
4.
Q)
Ifastation
has
been
previously
stored
using
the
same
channel
number,
it
will
be
erased
and
the
newly
selected
station
will
be
stored.
MEMORY
Receiving in Stereo or Mono
When an FM stereo broadcast is hard to receive or noisy:
() Press FM MODE/MUTE on the CA-S200 and the remote control so that reception
“IMUTE
improves,
although
you
lose
the
stereo
effect.
In
this
state,
you
will
hear
noise
while
tuning into stations.
Q)
Torestore
stereo
effect,
press
FM
MODE/MUTE
again
so
that
“AUTO”
appears
on
the
display.
In
this
state,
when
a
program
is
broadcast
in
stereo,
you
will
hear
stereo
sound;
when
in
monaural,
you
will
hear
monaural
sounds.
Furthermore,
in
this
state,
you
won’t
hear
noise while tuning to stations.
Page 9