(No.HC044<Rev.001>)1-21
5.1.2.2 Version of CPU and program display
(1) Turn ON the power. (CAM mode, MENU is undisplayed)
(2) The following operations are performed while holding down
the [OIS] button.
(3) While holding down the [USER1] button and the [USER2]
button, press the [MENU] button (less than 1 second).
(4) While holding down the [OIS] button, the [MENU] button is
pressed again.
(5) Move the cursor to [VERSION CHECK], then press the
[SET] button. Then the version of each CPU and a program
is displayed.
5.1.2.3 SERVICE MENU display
(1) Turn ON the power. (CAM mode, MENU is undisplayed)
(2) The following operations are performed while holding down
the [OIS] button.
(3) While holding down the [USER1] button and the [USER2]
button, press the [MENU] button (less than 1 second).
(4) While holding down the [OIS] button and the [AF/MF] but-
ton, press the [MENU] button.
5.1.3 ADVANCED FUNCTION Menu operation
(1) Refer to 5.1.1 to display the SERVICE MENU.
(2) Move the cursor to [ADVANCED FUNCTION], then press
the [Set] button or the [Cross-Shaped] buttons (up/down) to
change the parameter.
(3) ADVANCED FUNCTION Menu is displayed.
(4) Move the cursor to the item to be changed, then press the
[Set] button or the [Cross-Shaped] button (right).
(5) The parameter blinks. Press the [Cross-Shaped] buttons
(up/down) to change the parameter.
(6) Press the [Set] button to set the parameter. The parameter
lights up.
(7) Move the cursor to [BACK], then press the [Set] button or
the [Cross-Shaped] button (right) to go back to the upper
layer and finish the setting.
*Available only when the Camera Resolution setting is
1920x1080, and the Frame & Bit Rate setting is 60i(HQ). Other-
wise, it becomes a gray display and no selection is available.
5.1.3.1 White blemish detection
(1) Open the MAIN MENU, then set [Camera Resolution] in
[Record Format] to 1920x1080, and [Frame & Bit Rate] to
60i(HQ).
(2) Open the ADVANCED FUNCTION Menu, choose the [PIX-
EL COMPEN DET], and then press the [Set] button.
[PIXEL COMPEN DET]
Since it is displayed as Detect Pixel Compensation?, [De-
tect] is chosen and the [SET] button is pressed.
NOTE:
An error is displayed when SD card is not inserted.
NOTE :
• To cancel the parameter setting change, press the [Cross-
Shaped] button (left) while the item is chosen.
Version Check
Package SPL2470 V0002
CAM SPL2471 V0001
MBE SPL2472 V0002
MBE Loader SPL2473 V0001
EEPROM SPL2476 V0001
FPGA SPL2458 V830A
Back
Service Menu
Advanced Function...
Service Function...
DIP SW...
Hour Meter...
EEPROM...
Exit
Item Parameter
PIXEL
COMPEN
DET*
OP TEMPER-
ATURE
NEED OVER
47.5°C
The temperature information on
OP block is displayed.
In the case of a white blemish ad-
justment start, it recommends that
it is over this temperature.
LOOP REC OFF Loop REC is OFF.
ON Loop REC is carried out infinitely.
Advanced Function
Pixel Compen Det
OP Temperature 40.0
o
C(104.0
o
F)
need over 47.5
o
C
Loop Rec Off
Back
Record Format
System Definition HD(MPEG2)
File Format Quick Time
Camera Resolution 1920x1080
Frame & Bit Rate 60i(HQ)
Aspect Ratio 16:9
Set
Cancel
Advanced Function
Pixel Compen Det
OP Temperature 42.5
o
C(108.5
o
F)
need over 47.5
o
C
Loop Rec Off
Back
Advanced Function
Detect Pixel Compensation?
Detect
Cancel
To Next Page
Loading...
