K-TRON K-Commander User Manual

805.91
K-Commander Loss-in-Weight Programming
Rev: G Produced by the K-Tron Institute
Index
A
Acknowledged Alarm, 37
Actual Current Massflow, 12
Actual Motor Power, 66
Adaptive Tuning, 1
Adaptive Tuning Enabled, 77
Alarm Acknowledge, 37, 80
Alarm Clear, 80
Alarm Clear, 37
Alarm Delay Setting, 41
Alarm message table with cause and remedy, 31
Alarm Shutdown Mask, 62, 89
Alarm Shutdown Message, 36
Alarm type definitions, 37
All, 69
Allowed Refill Time, 23
ALSHUT, 5
Average Feedfactor, 16
B
Basics of SPC operation, 83
Basics of SPC operation- messages, 85
Basics of SPC operation, key descriptions, 86
Basics of SPC operations - displayed values, 84
Bit Input 1, 63
Bit Input 2, 63
Bit Input 3, 63
Bit Input 4, 63
Bit Output 1, 63
Bit Output 2, 63
Bit Output 3, 63
Bit Output 4, 64
Board Reset Message, 36
C
Calib DC (LWF only), 62
Calib. Correlation Limit, 19
Calibrate Cycle, 20
Calibrate Drive Command, 18
Calibrate Time, 18, 67
Changing a variable, 7
Chart Scaling Factor, 82
Cleaning or emptying the feeder hopper, 29
Clear Alarms on Stops, 42
Common message listing with resolution, 9
Controller Board Failure Alarm, 35
D
Definitions, 1
Density Array, 1
Density Array On/Off, 17
Determining scale range for entry on page 05, 47
DISA, 5
Display action line above the function keys, 5
Display Board Failure, 35
Drive Comm Greater than DHS Alarm, 31
Drive Comm less that DLS Alarm, 31
Drive Command, 1, 13
Drive Command High Alarm Limit, 40
Drive Command Low Alarm Limit, 40
Drive Command Low Message, 36
E
Edit Mode, 3
Ext. Totalizer Increment, 57
Ext. Totalizer Pulse, 62
External Alarm Active Alarm, 31
External Display Message, 36
F
F1, 3
F2, 3
F5, 3, 6
F6, 4, 6
F7, 4, 6
F8, 6
Fdr Controller Timeout Alarm, 31
Fdr Internal Channel Failure Alarm, 31
Feed Factor Alarm, 32
Feeder Invalid Command Alarm, 32
Feeder Mode, 59
Feeder Range Error Alarm, 32
Feeder Run Time, 77
Feeder stopped by conditions, 36
Feeder Tare Weight, 46
Feeder Type Selection, 57
FeedFactor, 2
Feedfactor Alarm Limit, 17
Feedfactor calibration procedure, 21
Feedrate, 2
FF Hopper Empty, 16
FF Hopper Full, 16
FF Hopper Mid, 16
FF0 thru FF10, 64
Fr6 Hyster, 66
Fr6 Offset, 66
Frequency In. 3 Deadband
Frequency Input. 3
Frequency Input #1-. 3 Value
Frequency Input 1-2, 71
Frequency Output 1-3, 71
FTS FDR 1, 66
FTS FDR 2, 66
FTS FDR 3, 66
Full Scale Drive Command, 59
Full Scale Drv Cmd, 62
Full Scale Setpoint, 56
G
Gear Reduction, 62
Gear Teeth, 62
Grav Mode, 3
Gravimetric control, 2
H
Hard Alarm, 37

K-TRON K-Commander Specifications

General

Brand	K-TRON
Model	K-Commander
Category	Control Panel
Language	English