K-TRON K-Commander User Manual

805.92
K10S Menu Display LWF Paging
Rev: G Produced by the K-Tron Institute
I
In this chapter, 1, 43
Initial Feedfactor, 15
I-O Board Failure Alarm, 33
L
Last Calib. Correlation, 19
Layout of often used keys, 3
Lo Motor Gain, 35
Load Scale Range, 63
Local Display Message, 36
Locked Out, 69
Loss of programming data, 8
Low Motor Gain Limit, 67
M
Massflow (-) Alarm Limit, 39
Massflow (+) Alarm Limit, 39
Massflow Filter Length, 76
Massflow Setpoint, 12
Massflow Standard Deviation, 2
Massflow Std Deviation, 76
Material Fed Last Calibration, 19
Material Net Weight, 12, 45
MDU Alarm, 32
Measured Gross Weight, 45
Measured Standard Deviation, 2, 75
Motor Control Gain, 76
Motor Drive Failure Message, 36
Motor Speed, 13
N
Nameplate Motor Power, 66
Nameplate Motor Speed, 66
Net Weight Low Alarm, 35
Net Weight Low Limit, 42
Node. of Selected SFT
Number of SFTs Required, 52
O
Order of data entry, an important point, 7
Overview page, 11
P
Page 00 layout, 11
Page 00 special key list, 13
Page 00 variable list, 12
Page 00 variable list con't, 13
Page 01 layout, 14
Page 01 special key list, 20
Page 01 variable list, 15
Page 02 layout, 22
Page 02 variable list, 23
Page 03 layout, 30
Page 03 special key list, 37
Page 04 layout, 38
Page 04 variable list, 39
Page 05 key list, 47, 54
Page 05 layout, 44
Page 05 variable list, 45
Page 06 layout, 51
Page 06 variable list, 52
Page 07 layout, 55
Page 07 variable list, 56
Page 08 layout, 70
Page 08 variable list, 71
Page 09 layout, 74
Page 09 variable list, 75
Page 10 graphic description, 79
Page 10 layout, 78
Page 10 special key list, 80
Page 11 layout, 81
Page 11 variable list, 82
Page 12 layout, 83
Page 13 description, 88
Page 13 layout, 87
Pending Alarm, 37
PERT, 5
Pert Residual, 67
Poll SFTs, 54
Post Refill Mode Delay, 25
Pre Load Totalizer, 62
Program variables and program priority protection table, 69
Programming Priority LCD, 60
R
Rate Greater than Setpoint Alarm, 33
Rate Less than Setpoint Alarm, 33
Refill Complete Weight, 2, 24
Refill Enable, 23
Refill Mode, 25
Refill Only Run, 62
Refill Request Weight, 2, 25
Refill Timer 2, 67
Refill Timer Expired Alarm, 33
Refill Timer Option, 24
Run Disable Message, 36
S
SAB Analog Input Assignment, 64
SAB Current Input Value, 64
SAB Input Calib Value, 64
SAB Input Range, 64
SAB Output 1 Calib Value, 65
SAB Output 2 Calib Value, 65
SAB Output 3 Calib Value, 65
SAB Output Assignment 1, 64
SAB Output Assignment 2, 64
SAB Output Assignment 3, 64
SAB Output Range 1, 65
SAB Output Range 2, 65
SAB Output Range 3, 65
SAB Output Value 1, 65
SAB Output Value 2, 65
SAB Output Value 3, 65
Scale Factor Input. 3
Scale Gross Weight Range, 45
Scale/SFT. \\"xx\\" Underrange Alarm. \\"xx\\" Overrange
Alarm
Scaled Frequency Input. 3
Selected SFT Status, 52
Service Variable Index, 61
Service variable index and value listing, 62
Service Variable Value, 61

K-TRON K-Commander Specifications

General

Brand	K-TRON
Model	K-Commander
Category	Control Panel
Language	English