CS-1022
CS-1021
0S"1012
CS-1020
CS-1010
Sweep Time
0.2
/is/div to 0.5 s/div,
±3% in 20
ranges,
in
1 -2-5
sequence.
Vernier control
provides
fully adjustable
sweep
time
between
steps.
0.5
/is/div to 0.5 s/div,
±3% in 19
ranges,
in
1-2-5
sequence.
Vernier
control provides
fully adjustable
sweep
time between
steps.
0.2
/is/div to 0.5 s/div,
±3% in 20
ranges,
in
1-2-5
sequence.
Vernier control
provides
fully adjustable
sweep
time between
steps.
0.5
/ts/div to 0.5 s/div,
±3% in 19
ranges,
in
1-2-5 sequence.
Vernier
control provides
fully adjustable
sweep
time between
steps.
Sweep Magnification
x 10 (ten times) ±5%
Linearity
±3%
all ranges,
±5%
on 0.2 /ts/div range at x 10 magnification.
TRIGGERING
Internal Sync
V. MODE; Triggered by input signal selected
by vertical MODE setting.
CH1;
Triggered by CH1 signal
CH2;
Triggered by CH2 signal
LINE;
Triggered by line voltage
INT;
Triggered by vertical input signal
LINE;
Triggered by line voltage
External Sync
EXT;
Triggered by signal applied to EXT
TRIG INPUT jack
External sync Input
Impedance
1
MS], ±2%
approx. 32pF
1
Mfi, ±2%
approx. 35pF
1
Mfi, ±2%
approx. 30pF
1 Mfi, ±2%
approx. 30pF
/^Maximum External
Trigger Voltage
50 V (DC + AC peak)
Coupling
AC,
VIDEO FRAME, VIDEO LINE
Tigger Sensitivity Tigger Sensitivity
FREQ,
RANGE INT EXT
FREQ,
RANGE INT EXT
FREQ,
RANGE INT EXT
FREQ,
RANGE INT EXT
FREQ,
RANGE INT EXT
Tigger Sensitivity
AUTO
20Hz
to 20MHz 1div 0.1Vp-p
20Hz
to 20MHz Idiv 0.2Vp-p
20Hz
to 10MHz
1
div
0.1
Vp-p
20Hzto20MHz
1div O.IVp-p
20Hz
to 10MHz Idiv
0.1
Vp-p
Tigger Sensitivity
NORM
10Hz
to 20MHz Idiv 0.1Vp-p
10Hzto20MHz
Idiv 0.2Vp-p
10Hzto10MHz
1
div
0.1
Vp-p
10Hzto20MHz
Idiv
0.1
Vp-p
10Hzto10MHz 1
div
0.1
Vp-p
Tigger Sensitivity
VIDEO
FRAME,
LINE Idiv 0.1Vp-p
FRAME,
LINE 1div 0.2Vp-p
FRAME,
LINE 1div
0.1
Vp-p
FRAME,
LINE
1
div
0.1
VPD
FRAME,
LINE
1
div
0.1
Vp-p
PROBE ADJ. VOLTAGE
0.5 V, ±6%, square wave, positive polarity, approx. 1 kHz
INTENSITY MODULATION
Sensitivity
TTL compatible
Positive voltage increases brightness.
Negative voltage decreases brightness.
Input Impedance
Approx. 10 kfi
Usable Frequency Range
DC to 2 MHz
DC to 1 MHz
DC to 2 MHz
DC to
1
MHz
^Maximum Input Voltage
50 V (DC + AC peak)
VERTICAL AXIS SIGNAL
OUTPUT
CH1
SIGNAL OUTPUT
—
CHI
SIGNAL OUTPUT
VERTICAL
SIGNAL OUTPUT
Output Voltage
Approx.
50mV/div
(50 Q
load)
—
Approx. 50
mV/div
(50 fi load)
Output Impedance
Approx. 50 Q
Approx. 50 fi
Frequency Response
100 Hz to 20 MHz,
-3 dB (50 0 load)
100 Hz to 10 MHz,
-3 dB (50 Q load)
100 Hz to 20 MHz,
-3 dB (50 fi load)
100 Hz to 10 MHz,
-3 dB (50 fi load)
TRACE ROTATION
Electrical,
adjustable from front panel
POWER REQUIREMENT
AC 100 V/120 V/220 V ±10%, 216-250 V 50/60 Hz
Power Consumption
Approx. 43 W Approx. 39 W
Approx. 41W
Approx. 38W
Approx. 36W
DIMENSIONS
( ) dimensions include protrusions from basic outline dimensions.
Width
260 mm (260 mm)
Height
160 mm (180 mm)
Depth
400 mm (460 mm)
5
To Next Page
Loading...
Need help?
General
