32
4.5
Performance
Editor
assignments
(Performance
Editor
Define)
For each
program
in Performance mode,
you
can assign
program
parameters
to knobs
1-5
for realtime
control of the sound. For
each
program
you
can
make
four sets of Performance Editor settings. These
settings are
made
in Performance Editor Define. In the following pages, the explanation will continue
the
procedure
given in "4.2 Editing a program," using the
program
you initialized
and
then modified.
The initialized
program
has the following settings.
PE
PEl
PE2
PE3
PE4
KNOB No. Assign Parameter Knob Left Knob Right
Curve
KNOB1
OSC1
__
0ctave
000%
100%
LINER
KNOB2 Std1_Wave
000%
100%
LINER
KNOB3
Stdl_FiampLevel
000%
100%
Exp
KNOB4 Std1_ WaveForm
000%
100%
Exp
KNOB5
Delay
__
Balance
000%
70%
Exp
KNOB1
OSC2
__
Octave
000%
100%
LINER
KNOB2 Std2_Wave
000%
100%
LINER
KNOB3 Std2_1RampLevel
000%
100%
Exp
KNOB4 Std2_WaveForm
000%
100%
Exp
KNOB5 Chorus_Balance
000%
70%
Exp
KNOB1 Filter1_Fc
000%
100%
LINER
KNOB2
Filter1_Resonance
000%
90%
LOG
KNOB3
Filter1
FcEGint
000%
100%
LINER
KNOB4 EG3_AttackTime
000%
100%
LINER
KNOB5 EG3_1DecayTime
000%
100%
LINER
KNOB1
Filter:!_FC
000%
100%
LINER
KNOB2 Filter:!_Resonance
000%
90%
LOG
KNOB3
Filter:!FcEGint
000%
100%
LINER
KNOB4
EG3_StartLevel
000%
100%
LINER
KNOB5 EG3_)l.ttackLevel
000%
100%
LINER
From Performance mode, press the
PE
DEFINE key.
The
PE
DEFINE key
LED
will light,
and
you will enter Performance Editor Define. The
PE
key being
edited will blink.
~
Use
the
PAGE
keys
to
move
to PED-1
[PEl
Definition].
Here
you
can
specify
the
parameters
that
will be controlled by
each
knob for
PEl.
Rotate knob 1
and
check
that
#1-#5 are set as
shown
in
the PEl area of the above table.
These settings determine which parameters will
be
assigned to each knob
when
PEl
key is pressed.
Rotate
knob
2.
Notice
how
the
assigned
parameter
changes.
Here
you
can
select
the
parameter
that
will
be
assigned to the knob.
The
display
shows
an
abbreviation of the
parameter
name
that
would
be
displayed
fully in Edit
mode. For the correspondence between the abbreviation
and
the full
parameter
name, refer to the
"Performance
Editor
Assign
List"
in
the
appendix
of
the
separate
"Parameter
Guide."
The
percentages
shown
in brackets indicate the value relative to the range of the values that can
be
set in
Edit mode.
Rotate knob
3.
This setting specifies the effect
produced
by moving the knob to the far left
position
in
Performance mode. Listen to the effect
on
the
sound
as
you
modify the value.
Knob 4 specifies
the
effect
produced
by
moving
the
knob
to
the
far
right
position
in
Performance mode. Set the value
in
the same way. Use the
CURSOR<
key to
return
to
the
Assign
Parameter
that
you set
in
step
[ji . Notice
that
the
sound
changes
here
as
well. This is
because
the
assigned
parameters
have
returned
to
the
values
of
their
settings.
liD
The indication of "LINEAR" at the right allows
you
to select
one
of
three curves
that
will
determine
how
the
sound
changes
when
you
operate the knob selected
in
~
.
This completes settings for
PEl.
Use the PAGE keys to
move
to PED-2-PED-4,
and
make
settings for
PE2-PE4.
To Next Page
Loading...
