•writing
procedure
Press the WRITE key.
The WRITE key LED
and
the
bank
LED of the writing destination will light,
and
the LEDs
of
the
available banks
and
the ENTER key LED will blink.
The
display
will indicate
the
current
program
parameter
load
source in the
upper
line,
and
the
writing destination in the lower line.
I
,.·.'''
0
!'
..
·;··,
····:·,!''
.......
,
;::::·:
...
,[!
·-
..
I
*
If
memory
protect
is
ON,
an
error
message
will
be
displayed.
Press
the
EXIT
key
to
return
to
the
previous
display.
Set
the
Edit
mode
Global
section,
page
GLB-20
[Memory
Protect]
parameter
to
OFF.
•
If
you
wish
to
return
to the
display
you
were
in
previously,
press
the EXIT key.
!g)
Using the A,
B,
or CARD*
1
keys, specify the writing destination bank.
*
1
Cif
the
CARD
key
LED
is
unlit,
pressing
the
CARD
key
will
produce
an
error
message.
If
you
wish
to
write
into
the
CARD
bank,
you
must
set
the
write
protect
slider
of
the
card
to
the
OFF
position
before
inserting it
into
the
card
slot.
Use the VALUE keys, numeric keys, or knob 1 to specify the writing destination program
number.
To
confirm the writing destination
program
number
you
specified
in
steps
[g}
and
~
, press the ENTER key.
The following display will appear,
and
the ENTER key LED will blink faster.
• To cancel,
press
the
EXIT key.
If
you
then
press
the
EXIT
key
once again,
you
will
return
to
the
display
you
were
in
before
initiating
the
Write operation.
If
you
are sure
that
you want to write the data, press the ENTER key. The data will be
written.
When
execution is complete, you will
return
to the display
you
were in before initiating the Write
operation.
•
If
you
decide
to cancel
the
Write
operation,
press
the
EXIT key. You
will
return
to the
display
of
step
[J}.
If
you
then
press
the
EXIT
key
once
again,
you
will
return
to
the
display
you
were
in
before
initiating
the Write operation.
4.4
Compare
By pressing this key
during
editing, you can recall the
unedited
settings. The
data
being edited will
be
held
in
internal
memory
until the next time
you
edit.
When
you
press
this key once again, the
edited
data
will
be
recalled.
Be
aware that
if
you
edit
parameters
while the LED
of
the COMPARE key is lit,
you
will lose the edits that
you
made
before pressing the COMPARE key.
If
you
enter
Performance
mode
without
writing
your
edited
data,
the
bank
name
shown
in the
upper
left of the
display
will
appear
in lower-case characters. As
long
as
you
do
not
change
programs,
the
COMPARE key will still act as explained above.
Even
if
you
return
to Performance
mode
without
writing
your
edited
data
and
then
select
another
program
number, you will still
be
able to recall
your
edited data. Press the COMPARE key
and
the
bank
name
(of Performance mode) will change to lower-case characters,
and
the edited
data
will be recalled.
Press the key once again
and
the
LED
will go out,
and
the currently selected
program
number
will
be
recalled.
If
you
write the edited data, the Compare function will
not
be available.
31
To Next Page
Loading...
