34
4.
7 Creating
Pattern
parameters
(Pattern
Define
Now
let's
try
creating
an
arpeggio
pattern
as
shown
in the following
musical
example.
*
When
you
modify
a
parameter
value
in
Pattern
Define
mode,
the
settings
are
stored
as
soon
as
you
make
them.
When the following notes are pressed
I'
I
11-......._
I'
ll=j
J
j
J
J
J
J
J
=II
Return
to
Performance
mode.
Press
a P AT1
key
to
select
a
user
pattern.
Press
the
PATTERN DEFINE key once again to
turn
on
the LED
and
enter Pattern Define mode.
If
an
arpeggio is playing, press the ARPEGGIO
ON
I OFF key to stop playback.
liJ
Use the PAGE keys to move to PATl-1 [Arpeggio Param],
and
use knob 1 to set "StB:
}"
and
knob 2 to set "Sort:ON".
@I
Use
the
PAGE keys to
move
to
PATl-5
[Step Param]. The "St#01"
parameter
at
left
indicates the step
number
of the pattern. Each user pattern can contain
up
to
24
steps,
and
the arpeggiator will play each note from the first step
at
intervals of the step base. You can
use the knob to move
through
the steps St#01-24 to check the settings of each step. The
"Tone:XX"
parameter
specifies
which
of
the
notes
being
pressed
will
be
sounded.
A
setting of "Tone:01" specifies the lowest note. (However this is
in
the case of Sort:ON.
If
Sort:OFF, this will refer to the note that
was
first pressed
on
the keyboard.) "Vel:XXX"
and
"Gt:XXX%" indicate the velocity
and
gate time of each step. The "Ofst+XX%" parameter is
an
offset that allows
you
to move the timing of each note backward
or
forward relative to
the step base.
I'
II:]
J
St#Ot I I 'Bl#02
Ofst+OO%
_
'9fst·49%
I
'ooli;~
~,.00~
j
St#03
I
Ofst+OO%
Tone:03
}
J
. St#04
:_lotst+49%
[ Tone:04
Here's
how
to specify the first step. Rotate knob 1 to select St#01,
and
rotate knob 2 to select
Tone:Ol. In the same way, make settings for St#02-St#09 as follows.
St#01
Tone:01
Vel:100 Gt:080%
Ofst+OO%
St#02 Tone:02
Vel:lOO
Gt:080%
Ofst+OO%
St#03
Tone:03 Vel:100 Gt:080%
Ofst+OO%
St#04 Tone:02
Vel:100 Gt:080%
Ofst+OO%
St#05 Tone:04
Vel:lOO
Gt:080%
Ofst+OO%
St#06 Tone:02
Vel:100 Gt:080%
Ofst+OO%
St#07 Tone:03
Vel:100 Gt:080%
Ofst+OO%
St#08 Tone:02
Vel:100 Gt:080%
Ofst+OO%
St#09 Tone: LOOP
Vel:lOO
Gt:080%
Ofst+OO%
The setting of "Tone:
LOOP"
for step St#09 causes the arpeggiation to return to the first step
at
this point.
(ID
Press the ARPEGGIO
ON
/OFF key to make it light, and press the
C-
E-
G-
B notes on the
keyboard.
The phrase of the above musical example will be played.
~
Make changes to the velocity, gate time
and
offset settings of each step,
and
listen to the
result.
Make sure that PATl-2 [Velocity Param] is set to
Vel:STEP,
and
that
PATl-3 [Gate Param]
is set to Gt:STEP. With these settings, velocity
and
gate time will be
determined
by
the
settings for each step.
To Next Page
Loading...
