Kyocera FS-9120DN User Manual

Chapter 3 Using the Operator Panel
3-21
Press the  key. Each time the  or  key is
pressed, the display changes as shown below.
The following example explains how to activate TCP/
IP protocol to connect the printer in the network.
You can select Netware or EtherTalk in a similar
manner.
If TCP/IP is currently displays Off, select On using
the  or  key. Press the ENTER key again.
Press the  key. Each time the  or  key is
pressed, the item changes as shown below.
Display the item to be set and press the ENTER key.
For DHCP, a question mark (?) appears. For IP Ad-
dress, Subnet Mask, and Gateway, the cursor (_)
blinks.
For DHCP, select On or Off using the  or  key.
For IP Address, Subnet Mask, and Gateway ad-
dresses, press the  or  key to change the number
(000 to 255) where the cursor is blinking. You can
use the  and  key to move the cursor right and
left.
To obtain these addresses, consult your network
administrator.
Press the ENTER key.
Press the MENU key. The message display returns to
Ready.
Printing a Network Interface Status Page
You can print out a status page for the network interface. The
network interface status page shows the firmware version,
the network addresses, and other information under various
network protocols about the network interface. The default
setting is On (print). The network interface status page will
be printed out after the printer status page.
Printing out a network interface status page may not be pos-
sible with some optional network interface cards. For details,
see the manual for the network interface.
>NetWare
On
>TCP/IP
On
>EtherTalk
Off
>Network Status
Page On
If ON, print the stan-
dard Network Inter-
face Status Page after
the Printer Status
Page. See
page 3-11 .
>Opt. StatusPage
On
If ON, print the op-
tional Network Inter-
face Status Page after
the Printer Status
Page. See
page 3-11 .
>TCP/IP >
On
>TCP/IP
? Off
>TCP/IP >
On
6
7
>>DHCP
Off
>>IP Address
000.000.000.000
>>Subnet Mask
000.000.000.000
>>Gateway
000.000.000.000
NOTE
8
9
10
11
12

Kyocera FS-9120DN Specifications

General

I/O ports	1 x Fast Ethernet 10/100 Base TX; 1 x High speed bi-directional parallel (IEEE 1284); 1 x USB 2.0 (High-Speed); 1 x KUIO LV Option-Interface slot.
Custom media sizes	88 x 148 mm - 297 x 450 mm
Power requirements	AC 220/240 V 50/60 Hz
Standard input trays	2 x 500
Recommended media weight	60 - 105 g/m²
Power consumption (active)	920 W
Maximum print size	297 x 420 mm
Maximum ISO A-series paper size	A3
Color	No
Print technology	Laser
Time to first page (black, normal)	7 s
Print speed (black, normal quality, A4/US Letter)	36 ppm
Memory slots	2
Storage media	HDD
Processor model	Power PC 750CX
Built-in processor	Yes
Maximum internal memory	544 MB
Internal storage capacity	20 GB
Sound power level (standby)	39 dB
Sound pressure level (printing)	53 dB
Total input capacity	1200 sheets
Maximum input capacity	4200 sheets
Paper tray 2 input capacity	200 sheets
Maximum duty cycle	55000 pages per month
Sustainability certificates	ENERGY STAR
Power consumption (standby)	160 W
Power consumption (PowerSave)	12 W

Weight and Dimensions

Dimensions (WxDxH)	585 x 639 x 615 mm