Kyocera FS-9120DN User Manual

Chapter 3 Using the Operator Panel
3-46
Press the MENU key.
Press the  or  key repeatedly until Paper
Handling > appears.
Press the  key. >Stitch Adjust > appears.
Press the  key. >>A4/Letter appears.
Press the  or  key to select A4/Letter, B4 or
A3/Ledger.
When the desired paper size is displayed, press the ENTER
key. A blinking cursor (
_
) appears under the value.
Press the  or  key to increase or decrease, respec-
tively, the value at the blinking cursor. Use the 
and  keys to move the cursor right and left.
Definable value: -057 to 057
When the desired value is displayed, press the
ENTER key.
Press the MENU key. The message display returns to
Ready.
Overriding A4 and Letter Size Difference
This selects whether to enable or disable the difference be-
tween A4 size and Letter size. Under the default setting of
Off, the paper size of the paper source is matched to the pa-
per size formatting the jobs. If these differ, a corresponding er-
ror message is displayed. When this is set to On, printing is
performed even if the actual paper size differs from the paper
size formatting the jobs.
Press the MENU key.
Press the  or  key repeatedly until Paper
Handling > appears.
Press the  key.
Press the  or  key repeatedly until >Override
A4/LT appears.
Press the ENTER key. A blinking question mark (?)
appears.
Select On or Off using the  or  key.
Press the ENTER key.
Press the MENU key. The message display returns to
Ready.
Customizing Paper Type
The following describes the procedure used to set a user-de-
fined paper type for the printer. Eight custom user settings
may be registered. After having been set, any of these may
be called up when setting the paper type for a paper source.
The paper weight and duplex path can be set (see
Setting the
Paper Weight on page 3-47
, and Setting the Duplex Path on
page 3-47
) after selecting the paper type to be customized as
follows. For how to reset the customized settings, see
Resetting the Type Adjust on page 3-47 .
Press the MENU key.
Press the  or  key repeatedly until Paper
Handling > appears.
Press the  key.
Press the  or  key repeatedly until >Type
Adjust > appears.
Paper Handling >
>Stitch Adjust >
>>A4/Letter
000
>>A4/Letter
000
Paper Handling >
1
2
3
4
5
6
7
8
9
1
2
>Override A4/LT
Off
>Override A4/LT
? Off
Paper Handling >
>Type Adjust >
Custom 1
3
4
5
6
7
8
1
2
3
4

Kyocera FS-9120DN Specifications

General

I/O ports	1 x Fast Ethernet 10/100 Base TX; 1 x High speed bi-directional parallel (IEEE 1284); 1 x USB 2.0 (High-Speed); 1 x KUIO LV Option-Interface slot.
Custom media sizes	88 x 148 mm - 297 x 450 mm
Power requirements	AC 220/240 V 50/60 Hz
Standard input trays	2 x 500
Recommended media weight	60 - 105 g/m²
Power consumption (active)	920 W
Maximum print size	297 x 420 mm
Maximum ISO A-series paper size	A3
Color	No
Print technology	Laser
Time to first page (black, normal)	7 s
Print speed (black, normal quality, A4/US Letter)	36 ppm
Memory slots	2
Storage media	HDD
Processor model	Power PC 750CX
Built-in processor	Yes
Maximum internal memory	544 MB
Internal storage capacity	20 GB
Sound power level (standby)	39 dB
Sound pressure level (printing)	53 dB
Total input capacity	1200 sheets
Maximum input capacity	4200 sheets
Paper tray 2 input capacity	200 sheets
Maximum duty cycle	55000 pages per month
Sustainability certificates	ENERGY STAR
Power consumption (standby)	160 W
Power consumption (PowerSave)	12 W

Weight and Dimensions

Dimensions (WxDxH)	585 x 639 x 615 mm