Kyocera FS-9120DN User Manual

Chapter 3 Using the Operator Panel
3-53
Press the ENTER key. A blinking cursor (_) appears.
Press the  or  key to increase or decrease the val-
ue of the figure where the cursor is blinking and set
the desired time. The time must be set between 000
and 495 seconds, in 5-second increments. If set to
000, printing will be continued immediately without
allowing any time interval. You can use the  and 
keys to move the cursor right and left.
Display the desired time and press the ENTER key.
Press the MENU key. The message display returns to
Ready.
Finishing
These settings are possible only when the optional finisher is
installed on the printer.
Duplex Printing Error Detection Setting
This setting controls whether or not the message
Duplex
disabled Press GO appears when label or some other type
of paper that is not supported for duplex printing is specified
as the paper type when duplex printing is being performed.
Press the MENU key.
Press the  or  key repeatedly until Others > ap-
pears.
Press the  key.
Press the  or  key repeatedly until >Finishing
Error > appears.
Press the  key.
Press the  or  key repeatedly until >>Duplex
appears.
Press the ENTER key. A blinking question mark (?)
appears.
Press the  or  key to change Off to On.
Press the ENTER key.
To exit the menu selection, press the MENU key.
Staple Error Detection Setting
This setting controls whether or not message Add staples
appears when the finisher units runs out of staples during
output of a stabled job.
Press the MENU key.
Press the  or  key repeatedly until Others > ap-
pears.
Press the  key.
Press the  or  key repeatedly until >
Finishing Error > appears.
Press the  key.
>>Auto Continue
Timer 030
Sec.
On
• Press the GO key to perform simple printing.
• Press the CANCEL key to cancel the print job.
Off
Disable duplex printing. (reverts to simplex
printing)
Others >
>Finishing >
Error
6
7
8
9
1
2
3
4
5
>>Duplex
OFF
>>Duplex
? Off
On
Message is displayed and printing pauses.
Printing resumes automatically when staples
are replenished.
Off
Message is displayed, but printing continues
without stapling.
Others >
>Finishing >
Error
6
7
8
9
10
1
2
3
4
5

Kyocera FS-9120DN Specifications

General

I/O ports	1 x Fast Ethernet 10/100 Base TX; 1 x High speed bi-directional parallel (IEEE 1284); 1 x USB 2.0 (High-Speed); 1 x KUIO LV Option-Interface slot.
Custom media sizes	88 x 148 mm - 297 x 450 mm
Power requirements	AC 220/240 V 50/60 Hz
Standard input trays	2 x 500
Recommended media weight	60 - 105 g/m²
Power consumption (active)	920 W
Maximum print size	297 x 420 mm
Maximum ISO A-series paper size	A3
Color	No
Print technology	Laser
Time to first page (black, normal)	7 s
Print speed (black, normal quality, A4/US Letter)	36 ppm
Memory slots	2
Storage media	HDD
Processor model	Power PC 750CX
Built-in processor	Yes
Maximum internal memory	544 MB
Internal storage capacity	20 GB
Sound power level (standby)	39 dB
Sound pressure level (printing)	53 dB
Total input capacity	1200 sheets
Maximum input capacity	4200 sheets
Paper tray 2 input capacity	200 sheets
Maximum duty cycle	55000 pages per month
Sustainability certificates	ENERGY STAR
Power consumption (standby)	160 W
Power consumption (PowerSave)	12 W

Weight and Dimensions

Dimensions (WxDxH)	585 x 639 x 615 mm