Why are my Kyocera TASKalfa 220 printouts wrinkled?
If your Kyocera All in One Printer produces wrinkled printouts, the paper separator of the paper feed unit might be dirty; clean the paper separator. Also, if the paper is damp, replace it with new paper.
What to do if Kyocera TASKalfa 220 ejects blank sheets?
If your Kyocera All in One Printer ejects blank sheets, when placing originals on the platen, make sure to place them face-down and align them with the original size indicator plates. When placing originals in the optional document processor, place them face-up.
How to remove black lines from Kyocera TASKalfa 220 document processor printouts?
If you see black lines on printouts from the document processor of your Kyocera All in One Printer, it's likely that the slit glass is dirty. Clean the slit glass to resolve this issue.
Why are images skewed on my Kyocera TASKalfa 220 All in One Printer?
To resolve images being skewed on your Kyocera All in One Printer, ensure the originals are placed correctly against the Original Size Indicator Plate when placing the original on the platen. When using the optional document processor, align the original width guides securely before placing the originals. Also, check the position of the paper width guides to ensure the paper is loaded correctly.
How to adjust darkness on Kyocera TASKalfa 220 printouts?
If your Kyocera All in One Printer's printouts are too dark, and the machine is in Auto Density mode, set the correct density level. If the machine is in Manual Density mode, use the Image Quality selection key to set the correct density level.
What to do if pressing Start key on Kyocera All in One Printer doesn't make copies?
If pressing the Start key on your Kyocera All in One Printer doesn't produce copies, it could be due to a message on the touch panel. Determine the appropriate response to the message and respond accordingly. Alternatively, the printer might be in Sleep mode. Press the Power key to recover the machine from Sleep mode, and it will be ready to copy within 1 second.
What to do when Kyocera All in One Printer says 'Add toner'?
If your Kyocera All in One Printer indicates 'Add toner', replace the toner container with a new one.
Why are the printouts from my Kyocera All in One Printer dirty?
If your Kyocera All in One Printer's printouts are dirty, the platen or the original cover might be dirty. Clean the platen or the original cover. Also, the transfer roller might be dirty, so brush the transfer roller clean.
How to fix light printouts on Kyocera TASKalfa 220 All in One Printer?
If your Kyocera All in One Printer's printouts are too light, and the machine is in Auto Density mode, set the correct density level. If the machine is in Manual Density mode, use the Image Quality key to set the correct density level. Make sure the toner is distributed evenly within the toner container by shaking it from side to side several times. Replace the toner container if there's a message indicating the need for toner. Replace damp paper with new paper. Clean the electrical charge section using the Cleaning Rod after opening the front cover. Also, disable EcoPrint mode.
General| Functions | Print, Copy, Scan, Fax |
|---|---|
| Print Speed (Black/A4) | 22 ppm |
| Warm-up Time | 30 seconds or less |
| Print Resolution | 600 x 600 dpi |
| Memory (Standard) | 256 MB |
| Standard Paper Capacity | 250 sheets |
| Copy Speed | 22 cpm |
| Copy Resolution | 600 x 600 dpi |
| Fax Modem Speed | 33.6 kbps |
| Hard Drive | Optional |
| Operating Systems Supported | Windows, macOS, Linux |
| Monthly Duty Cycle | 30, 000 pages |
| First Print Time | 8.5 seconds or less |
| Paper Sizes | A4, A5, B5, Letter, Legal |
| Paper Output Capacity | 100 sheets |
| Scan Features | Scan to Email, Scan to Folder |
| Fax Compatibility | Optional |
| Fax Transmission Speed | 3 seconds per page |
| Fax Resolution | 200 x 200 dpi |
| Interface | USB 2.0, Ethernet |
| Display | LCD Display |
To Next Page
