What to do if pressing Start key doesn't produce copies on Kyocera TASKalfa 250ci?
If pressing the Start key on your Kyocera All in One Printer does not produce copies: * Determine the appropriate response to any message displayed and respond accordingly. * Press the Power key to recover the machine from Sleep mode. The machine will be ready to copy within 45 seconds.
Why do printouts from the document processor have black lines on my Kyocera All in One Printer?
If printouts from the document processor of your Kyocera All in One Printer have black lines, the slit glass may be dirty. Clean the slit glass.
How to fix Kyocera TASKalfa 250ci machine failure?
If your Kyocera All in One Printer is showing a machine failure message, try turning the main power switch off and on, or unplug the power cord and plug it in again. If the message persists, make a note of the error code, turn the main power switch off, unplug the power cord, and call your service representative.
Why do white or color streaks appear on prints from Kyocera All in One Printer?
If white or color streaks appear on prints from your Kyocera All in One Printer, the inside of the machine may be dirty. Carry out Laser Scanner Cleaning.
Why are printouts from my Kyocera TASKalfa 250ci fuzzy?
If printouts from your Kyocera All in One Printer are fuzzy, and the machine is being used in very humid conditions, carry out Drum Refresh.
Why are documents printed improperly from my Kyocera TASKalfa 250ci All in One Printer?
If documents are printed improperly from your Kyocera All in One Printer, check that the printer driver and application software settings are set properly on your PC.
How to fix light printouts on Kyocera All in One Printer?
If your Kyocera All in One Printer prints are too light, try these solutions: * If in Auto Density mode, adjust the density level. * If in Manual Density mode, use [Image Quality] to set the correct density. * Shake the toner container from side to side. * Replace the toner container if prompted. * Replace the paper if it's damp. * Perform Drum Refresh or Laser Scanner Cleaning. * Disable EcoPrint mode.
Why are my Kyocera All in One Printer's printouts dirty?
If your Kyocera All in One Printer is printing dirty outputs, clean the platen or document processor. If that doesn't work, brush the transfer roller clean, carry out a Drum Refresh, or perform Laser Scanner Cleaning. Also, you can disable the Printed Document Guard Kit.
Why does my Kyocera All in One Printer keep jamming?
If paper often jams in your Kyocera All in One Printer, make sure the paper is loaded correctly. If it is, remove the paper, turn it over, and reload it. Also, replace the paper if it's curled, folded, or wrinkled. Finally, remove any jammed paper or loose scraps from the machine.
What to do if my Kyocera All in One Printer won't print?
If you cannot print from your Kyocera All in One Printer, ensure the power cord is plugged into an AC outlet and the main power switch is turned on. Verify the printer cable is securely connected, and if the machine was powered on before connecting the cable, power it on again after connecting the cable. If 'Press Status Key...' is displayed, press the Status/Job Cancel key, then [Printing Jobs], and [Resume All Print Jobs].
General| Functions | Print, Copy, Scan, Fax |
|---|---|
| Copy Resolution | 600 x 600 dpi |
| Duplex Printing | Standard |
| Type | Color Multifunctional |
| Print Speed | 25 ppm |
| Print Resolution | 600 x 600 dpi, Multi-bit technology for print quality of 9, 600 x 600 dpi equivalent |
| Copy Speed | 25 copies per minute (A4) |
| Scan Resolution | 600 dpi |
| Fax Resolution | 200 x 200 dpi, 300 x 300 dpi |
| Memory | 1 GB |
| Hard Disk Drive | 80 GB |
| Network Connectivity | Ethernet, USB |
| Scan Features | Scan to e-mail, Scan to FTP, Scan to SMB, Scan to USB Host, TWAIN scan |
To Next Page
