Lenze 8104 - Page 70

68
81 00_ A T echnical description
Code level
Factory
I
customer
settings settings
* C176 Fl.M1Ction
tenftinals 21, 22
.C200
* C210 preselection:
Process control
step
PRG
<===>
Parameter level
-0- SH + PRG term. 21: Remove quick stop
do not invert set-value
SH + PRG term. 22: Removequick stop,
invert set-value
-.-.....---....---------.-.------------------------------
-,- SN + PRG tenn. 21: Inversion of set-value
term. 22: Remove quick stop
Change is only possible when controller inhibitedl
Code 200 contsios the corrplete software
identHication. It can only be read via the
lECetl interface.
preselect desired process control step using C210,
then enter set-yalue I..nderC211, Ti-times lßder
C212. dur8tion ender C213. next step under C214.
---------------------------------------------------------
-1- SH+ PRG Step 1
--------------------_._._-_._----------------------------
-2- SH+ PRG Step 2
--------------------_....--.--..........--....-------.-..
...
-----------------------......-_.........-....--------....
-8- SH+ PRG Step 8
. C211 Set.vatue tor
[2101
..................-.-------.--------------------------------........---.-------------
-1- SH+ PRG JOGset.v8lue 1
-0- SH+ PRG Set-v8lue 1 (C046)
.........................................................
.........-......................................-.-------
-2- SH+ PRG JOGset.v8lue 2
.........--......-._.......-.---...........-----------...
...
--------------------------...---.--------.........---.---
-15 SH+ PRG JOGset.v8lue 15
--------------------------...........................................---------_......
.C212 Ti time tor [C2101 I -0- SH+ PRG Ti time COI2/COI3
........................................----------_......
-1- SH+ PRG Ti time Tirl/Tifl
.........................................-._----------.--
-2- SH + PRG Ti time Tir2/Tif2
...-----....................-------.-.-----_..........-..
...
.........................................----------------
-15 SH+ PRG Ti time TirI5/Tif15
* C213 Duration
tor [210]
,........-.........------......................_.-.--.....
xxx 5 0.0.. .9900s
0.0. ..ls
1... lOs
10.. .100s
100...99Os
1000.. .9900s
99995 = infinite
-0-
.C214 Next step tor
[C210]
1 1...................__
-1- SH + PRG Step 1
.:~:.. ~~.:.~~~. .~~~~~~.~~~~~~~_~~~~~~~__ 1 St~~_ 1
.. .
-:~:..;~.:.;;~..;;~.~.. ..--- - ..-
1
Step 2
-3-
Step 3
-4-
--...........................------.---..........--------
-----.....-...---.----.........------------------........
-8- SH + PRG Step 8
Step 4
-5-
Step 5
-0-
...
Step 8
-0-
Lenze
00_0000 ._10000.......
Step 1
-1-
Step 2
-2-
.. .
Step 8
-8-
..... ..--1-00.... ....
Step 1
-1-
Step 2
-2-
...
Step 8
-8-
.00 _00 ...1......00 00_
Step 1
10.0s
{IOms}
{1oOms} I ...
{ls}
{lOs} Step 8
{100s} 10.0s