LG RC689D User Manual (English)

Questions and Answers:

S
Samantha HolmesAug 17, 2025
What to do if the LG DVD Player remote control does not work properly?
- C
  christopher79Aug 17, 2025
  The remote control may not work properly for several reasons: * Ensure the remote control is pointed at the remote sensor on the unit. * Make sure the remote control is not too far from the unit. * Check for any obstacles between the remote control and the unit. * Replace the batteries in the remote control if they are exhausted. * If you recently replaced the batteries, the remote’s manufacturer code may have returned to the default setting; in this case, reset the code (page 65).
M
Michael MendozaAug 19, 2025
What to do if the connected HDMI device does not display any picture with my LG RC689D?
- S
  sotochristianAug 19, 2025
  If the connected HDMI device does not display any picture, try the following: * Disconnect and then reconnect the HDMI cable. * Switch the power of the HDMI device off and then back on. * Ensure the video input of the connected device is set correctly for this unit. * Verify that the HDMI cable you are using is fully HDMI-compliant. * Note that not all HDCP-compatible DVI devices will work with this unit.
T
todd13Aug 22, 2025
What to do if the connected HDMI device does not output sound with my LG RC689D DVD Player?
- S
  sally67Aug 22, 2025
  The connected HDMI device may not output sound because: * Some HDMI-compatible devices do not output sounds (check the manual that came with the connected device). * If your TV is not capable of handling 96 kHz sampling frequency, set the [Sampling Freq.] option to [48 kHz] on the setup menu. * If your TV is not equipped with Dolby Digital and MPEG decoder, set the [Dolby Digital] and [MPEG] options to [PCM] on the setup menu. * If your TV is not equipped with DTS decoder, set the [DTS] options to [OFF] on the setup menu.
M
mooneyhollyAug 25, 2025
Why the LG DVD Player stereo audio record and playback is not present?
- W
  William WhiteAug 26, 2025
  Stereo audio record and playback might not be present if: * Your TV is not Stereo-compatible. * The broadcast programme is not in stereo format. * The A/V Output jacks on the unit are not connected to TV A/V In jacks.
D
Douglas CardenasAug 27, 2025
What to do if my LG DVD Player does not start playback?
- A
  Anthony GainesAug 28, 2025
  If your unit does not start playback, consider the following: * Ensure that you have inserted a playable disc, verifying the disc type, color system, and regional code. * Place the disc with the playback side down. * Make sure the disc is placed correctly on the disc tray inside the guide. * Try cleaning the disc. * Cancel the Rating function or change the rating level.
J
Joseph MckenzieAug 30, 2025
Why does my LG DVD Player timer record not record successfully?
- C
  Charles BeanAug 30, 2025
  Timer recording may fail if: * The clock is not set to the correct time. * The start time of the timer recording is in the past. * Two timer recordings overlap (only the earlier one will record completely). * The recorder’s built-in tuner is not set when setting the recording programme (ensure it's not the TV’s built-in tuner). * The inserted disc is damaged.
L
Lindsay HamiltonSep 2, 2025
Why does my LG RC689D cannot record or does not record successfully?
- D
  daniellehillSep 2, 2025
  Recording issues may occur due to: * Insufficient space on the disc. * Copy-protected source material. * Incorrect disc format for copy-once material (use a VR mode formatted disc). * Power failure during recording. * In DVD mode, attempting to record rated digital programs, no signal, audio only, or scrambled programs. * DTV rating settings that block higher-rated digital programs (change the DTV rating level to record).