Life GE UNI 24R - Initialisation Procedures

12
EL0030
EL0030
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
EL0023c
EL0023c
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
EL0023b
EL0023b
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
EL0031
EL0031
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
EL0016
EL0016
A
EL0036a
EL0036a
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
EL0016
EL0016
A
2) PedestriancommandidenticationtheredLED
(DX)willashslowlyandtheashinglightwillemit
doubleashes.
Press the key (A)ontheradiocontrol(s)(notma-
ster)thatonewantstoidentifyandholddownuntil
the green LED (DX) and the SPLENDORashing
lightlightbriey.
3) Radio control resetting: the red and green LEDs
(DX) and (SX)willashalternatelyandtheashing
lightwillemitatripleash.
Press the key (A)ontheradiocontrol(s)(notma-
ster)thatonewantstoresetandholddownuntilthe
green LED and the SPLENDORashinglightlight
briey.
4) Exit programming.
a)Thatthe2redLEDsash.
b) Check that the lateral LEDs L7 and L11 are
switched on.
c) Check that the lateral LEDs L8, L9 and L10 are
switched off.
If this does not occur, check the connections and
effectiveness of the various devices, assure that the
NC inputs for which no device is connected are
jumpered.
2.3.1 Travel and staggering identication
2.3.1.1 2-leaf gate
There are two initial programming modes available:
a) ONE TOUCH’: automatic programming in which the various operations are performed automatically with default settings established by
LIFE.Thismodeisrecommendedforlightweightleafsandopeningsofupto90°.
b) STANDARD:theinitialmanoeuvresarecontrolledbythetter.
A) ‘ONE TOUCH’ PROGRAMMING
a) Press .
b) Press the step command key (A) on the radio control: the automation will perform, in sequence, a closure, an opening, a closure.
c)Havingcompletedthegate(s)closeself-programming,thetwogreenLEDsashandtheredoneremainslit.
The automation is now in semi-automatic mode by default.
Performstandardinstallationifyouaredissatisedwiththeresultobtained.
2.3 INITIALISATION
ATTENTION: LIFE cards are multipurpose and may be used for several applications; therefore, on activation they require the identi-
cation of the type of automation that they will serve.
EL0043
EL0043
EL0043A
EL0043A
X2
EL0043
EL0043
EL0043A
EL0043A
X3
2)
3)
a)ThecontrolunitmustNOTbepoweredelectrically.
b)Releasetheactuator,positiontheleafsatapproximately50cmfromtheclosurepositionandre-lockthem.(OPERATORRELEASEChap.)
c)Pressandtogether,holdingthemdown,andswitchonthepowersupplytothecontrolunit.
d)ReleasethekeyswhentheredLEDlights
N.B.Theoperationsdescribedinpointc)andd)allowoperatoridenticationandhavealreadybeenperformedbytheManufacturer,itistherefore
sufcienttoswitchonthepowersupplyandcheck:.
ATTENTION: Each phase has a timed exit (after approx.15 secs.) from receiver programming feature.
L7
L8
L9
L10
L11
2 MAN.ISTRUZ.GE UNI24R (GB).indd 12 30-10-2008 16:41:17