Life GE UNI 24R - Starting Up and Initialisation; Initialisation and Programming

EL0024a
EL0024a
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
EL0025
EL0025
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
EL0021a1
EL0021a1
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
b) Simultaneously press and hold down and ,
switch on the power supply to the system to
light the third LED.
c) Release keys and , the two red LEDs will
now ash.
EL0013
EL0013
EL0028
EL0028
1
2
3
4
5
6
7
8
9
10
F1
F2
UOMOPRESENTE
SEMIAUTOMATICO
AUTOMATICO 2 PASSI
BLACH-OUT
AUTOMATICO 4 PASSI
CONDOMINIALE
PRELAMPEGGIO
LAMPEGGIO IN PAUSA
FOTO 1
CHIUDE PASSANDO
FOTO TEST
COLPO D`ARIETE
LUCE DI CORTESIA
RALL APERTURA
APERT. PEDONALE
FORZA
TEMPO PAUSA
RALLENTAMENTO IN CHIUSURA
SENSIBILITA` MOTO
EL0017
EL0017
9
EL0020
EL0020
EL0027
EL0027
10
EL0016
EL0016
A
a) If the automation has a single leaf press : the right
red LED will remain lit, the left one will ash. For
automations with two leafs, go directly to point b).
RADIO CONTROL IDENTIFICATION
ON THE STEP COMMAND (A)
EL0012a
1
EL0012a
EL0012
1
2
EL0012
PHASE 4
CARD INITIALISATION
PHASE 5
PROGRAMMAZIONE ONE TOUCH
3
a) Switch off power supply.
The automation is now in semi-automatic modebydefault.Performstandardinstallationifyouaredissatisedwiththeresultobtained.
b) 1. Press .
2. Press the step command key (A) on the radio control: the
automation will perform, in sequence, a closure, an
opening, a closure.
3. Having completed the gate(s) close self-programming,
the two green LEDs ash and the red ones will remain lit.
EL0020
EL0020
EL0015
EL0015
ON
230V
ON
OFF
230V
OFF
ENGLISH
EL0027
EL0027
10
2 MAN.ISTRUZ.GE UNI24R (GB).indd 3 30-10-2008 16:40:42