What to do if PWR LED is off on LSIS Controller?
If the PWR LED is off on your LSIS Controller, first verify that the rated voltage is being supplied to the PLC. If the voltage supply is normal, it may indicate a hardware problem. Contact an A/S office or customer center for assistance.
How to fix ERR LED flashing quickly on LSIS XEC-DN60SU Controller?
When the ERR LED is flashing quickly on the LSIS Controller, it indicates a serious problem that prevents operation. Access the XGB with XG5000, go to ‘Online’ -> ‘PLC error/warning’, then check the error and warning messages, and resolve the underlying cause.
Why is RUN LED off on LSIS Controller?
If the RUN LED is off on your LSIS Controller, it means that the program has stopped running. Check the ERR LED to determine if the program stopped due to an error or because the operation mode is set to STOP.
What to do if Positioning Output LED is off on LSIS XEC-DN60SU?
If the Positioning Output LED is off on the LSIS Controller, it indicates that the pulse is not being output normally, or the positioning operation has finished normally. If the operation finished normally, start the next operation instruction. If there is an error, check the positioning error code and resolve the cause.
What does it mean when ERR LED is on LSIS XEC-DN60SU Controller?
If the ERR LED is on for the LSIS Controller, there is a problem with the PLC hardware. Contact an A/S office or customer center for assistance.
Why is Positioning Output LED fast flashing on LSIS XEC-DN60SU Controller?
If the Positioning Output LED is flashing quickly, it means the pulse is being normally output by the positioning function. Check the lines of the XGB and motor driver to ensure there are no issues.
What does it mean when PWR LED is on LSIS Controller?
If the PWR LED is on for the LSIS Controller, the power supply is normal. Check whether there is another cause for the issue you are experiencing.
What does Direction Output LED On (HIGH Active) mean on LSIS XEC-DN60SU?
If the Direction Output LED is on (HIGH Active) for the LSIS controller, it means that direction signals are being output in the reverse direction, or the positioning operation has finished normally. Start the next operation instruction. If there is an error that makes positioning operation impossible, check the positioning error code and remove the cause.
What to do if PWR LED is flashing on LSIS Controller?
If the PWR LED is flashing on your LSIS Controller, check the voltage and current of the power supply. If the problem persists, remove the input and output lines, re-supply power, and check again. If the problem continues, contact the A/S office or customer center.
What does it mean when RUN LED is on LSIS XEC-DN60SU?
If the RUN LED is on for the LSIS Controller, it means the program is operating normally. Check whether there is another cause for any issues you might be experiencing.
Essential safety guidelines for operating and handling the equipment.
Covers essential steps and parameters required before starting positioning operations.
Explains the definitions, functions, and usage of various positioning instructions.
Guides users on identifying and resolving common errors and malfunctions.
Lists and describes positioning instructions and their corresponding K area addresses.
Safety precautions and guidelines for designing the system with the product.
Guidelines for safe and correct wiring procedures to prevent hazards.
Lists and describes various positioning functions like position control and speed control.
Details the sequence for setting positioning parameters and K area configuration.
Provides detailed descriptions and examples of various positioning instructions.
Explains general function blocks and common error codes for XEC PLC.
Describes how to check PLC status using LEDs for troubleshooting.
Guides on checking and removing causes of errors using error codes.
Details error codes specific to the XGB positioning function.
General| Model | XEC-DN60SU |
|---|---|
| Category | Controller |
| Series | XEC |
| Power Supply | 24V DC |
| Digital Inputs | 36 |
| Digital Outputs | 24 |
| Output Type | Transistor |
| Programming Software | XG5000 |
| Operating Temperature | 0°C to 55°C |
| Storage Temperature | -20°C to 70°C |
| Humidity | 5% to 95% RH (non-condensing) |
| Protection Class | IP20 |
| Product Type | PLC |
| Communication Ports | Ethernet, RS-232, RS-485 |
To Next Page
