To Next Page

To Previous Page



1-16

F - TAKING UP AND LAYING A HIGH LOAD ON TYRESF - TAKING UP AND LAYING A HIGH LOAD ON TYRES

You must not raise the jib if you have not checked the transverse attitude of the lift truck (see:You must not raise the jib if you have not checked the transverse attitude of the lift truck (see:

INSTRUCTIONS FOR HANDLING A LOAD: INSTRUCTIONS FOR HANDLING A LOAD: D - TRANSVERSE D - TRANSVERSE ATATTITUDE OF THE LIFT TRUCK).TITUDE OF THE LIFT TRUCK).

REMINDER:REMINDER: Make sure that Make sure that the following operations the following operations can be performed with good visibilitycan be performed with good visibility

(see: OPERATIONS INSTRUC(see: OPERATIONS INSTRUCTIONS UNLADEN AND LADEN: TIONS UNLADEN AND LADEN: D - VISIBILITY).D - VISIBILITY).

TAKING UP A HIGH LOAD ON TYRESTAKING UP A HIGH LOAD ON TYRES

- Ensure that the forks will easily pass under the load.- Ensure that the forks will easily pass under the load.

-- Lift and extend the jib (1) (2) until the fLift and extend the jib (1) (2) until the forks are level with the load, moving the lift truck (3)orks are level with the load, moving the lift truck (3)

forward if necessary (fig. F1), moving very slowly and carefully.forward if necessary (fig. F1), moving very slowly and carefully.

-- Always think about keeping the distance necesAlways think about keeping the distance necessarsary to fit the forks under thy to fit the forks under the load, betweene load, between

the pile and the lift truck (fig. F1) and use the shortest possible length of jib.the pile and the lift truck (fig. F1) and use the shortest possible length of jib.

-- Stop the forks in front Stop the forks in front of the load by alternately extending and of the load by alternately extending and retracting the jib (1) orretracting the jib (1) or, if, if

necessary, moving the lift truck forward (2) (fig. F2). Put the handbrake on and set thenecessary, moving the lift truck forward (2) (fig. F2). Put the handbrake on and set the

forward/reverse selector to neutral.forward/reverse selector to neutral.

-- Slightly lift the load (1) and inclinSlightly lift the load (1) and incline the carriage (2) backwards to stabe the carriage (2) backwards to stabilize the load (fig. F3).ilize the load (fig. F3).

- Tilt the load sufficiently backwards to ensure its stability.- Tilt the load sufficiently backwards to ensure its stability.

-- Watch the Watch the longitudinal stability alarm (see: INSTRUClongitudinal stability alarm (see: INSTRUCTIONS FOR HANDLING A LOAD: TIONS FOR HANDLING A LOAD: CC

- LONGITUDINAL STABILITY ALARM). If it is overloaded, replace the load - LONGITUDINAL STABILITY ALARM). If it is overloaded, replace the load in the place fromin the place from

which it was taken.which it was taken.

-- If possible lower the load If possible lower the load without shifting the lift truck. Lift the jib without shifting the lift truck. Lift the jib (1) to release the load,(1) to release the load,

retract (2) and lower the jib (3) to bring the load into the transport position (fig. F4).retract (2) and lower the jib (3) to bring the load into the transport position (fig. F4).

-- If this is not possibIf this is not possible, back up the lift truck (1), manole, back up the lift truck (1), manoeuvring very gently and carefulleuvring very gently and carefully toy to

release the load. Retract (2) and lower the jib (3) to bring the load irelease the load. Retract (2) and lower the jib (3) to bring the load into the transpornto the transport positiont position

(fig. F5).(fig. F5).

F1F1

F2F2

F3F3

F4F4

F5F5

https://www.forkliftpdfmanuals.com/