Why is there noise during AM reception on my Marantz Stereo Receiver?
If you hear noise during AM reception on your Marantz Stereo Receiver, it could be due to interference from other electrical fields. Try changing the location where the AM indoor antenna is set up.
Why is there no audio output from the surround back speakers on my Marantz Stereo Receiver?
If there is no audio output from the surround back speakers on your Marantz Stereo Receiver, check the following: * Ensure the surround back speaker cable is correctly connected. * Verify that the surround mode is set to EX/ES. * Confirm that "Surround back = NONE" has not been selected in SPEAKERS SIZE SETUP. Make the correct setting.
Why no audio output from surround speakers on Marantz Stereo Receiver?
If you're not getting any audio output from the surround speakers on your Marantz Stereo Receiver, here's what to check: * Ensure the surround speaker cable is correctly connected. * If "STEREO" is selected for Surround mode, no sound will come from the surround speakers. Choose a different Surround mode. * Verify that "Surround = NONE" is not selected in SETUP mode. Make the correct setting.
What to do if control with the remote control unit fails on Marantz Stereo Receiver?
If your Marantz Stereo Receiver remote control isn't working, try these steps: 1. Replace all the batteries with new ones. 2. Ensure you are selecting the correct function-key setting for the equipment you are controlling. 3. Move closer to the SR4500. 4. Remove any objects blocking the path between the remote and the SR4500.
What to do if there is no output to Sub Woofer Out on Marantz Stereo Receiver?
If there is no output to the subwoofer on your Marantz Stereo Receiver, check if "Sub-woofer = NONE" has been selected in the SETUP mode. If so, select "Sub-woofer = YES".
How to fix FM or AM reception failure on Marantz Stereo Receiver?
If FM or AM reception fails on your Marantz Stereo Receiver, it might be due to an incomplete antenna connection. Ensure that the indoor FM and AM antennas are correctly connected to the FM and AM antenna outlets.
What to do if my Marantz Stereo Receiver has no sound and picture?
If your Marantz Stereo Receiver has no sound and picture output even when powered on, it could be due to several reasons: * The mute function might be activated. Deactivate mute using the remote control. * Incorrectly connected input cables. Refer to the connection diagram to ensure correct cable connections. * The master volume might be set too low. Adjust the master volume to an audible level. * The function selector might be set to the wrong position. Ensure the correct function is selected.
What to do if Incorrect Audio from a channel on Marantz SR4500 Stereo Receiver?
If the audio from a channel is incorrect on your Marantz Stereo Receiver, it may be due to the speaker cable being connected incorrectly. Refer to the connection diagram to connect the cable correctly.
Why is there no speaker output on Marantz SR4500 Stereo Receiver?
If you're not getting any speaker output from your Marantz Stereo Receiver, check if headphones are connected to the headphone jack. Disconnect the headphones, as speakers will not output sound when headphones are connected.
Why FM or AM reception fails on Marantz Stereo Receiver?
If you're not getting FM or AM reception on your Marantz Stereo Receiver, make sure the indoor FM and AM antennas are correctly connected to the FM and AM antenna outlets.
General| Frequency Response | 10Hz-100kHz (+1, -3 dB) |
|---|---|
| Total Harmonic Distortion | 0.08% |
| Input Sensitivity | 200mV (line) |
| Tuning range | FM, AM |
| Damping Factor | 100 |
| Input Impedance | 47k ohms |
| Power Output | 90W per channel (8 ohms, 20Hz-20kHz, THD 0.08%) |
| Signal-to-Noise Ratio | 105dB (line) |
| Video Connections | Composite, S-Video |
| Digital inputs | Optical, Coaxial |
| Speaker Impedance | 6-8 ohms |
To Next Page
