SURROUND MODES AND PARAMETERS
Sound modes and channel output
S This indicates the audio output channels or surround parameters that can be set.
DThis indicates the audio output channels. The output channels depend on the settings of “Speaker Config.” (v
p. 189).
Sound mode (v p. 118)
Channel output
Front L/R Center Surround L/R Surround back L/R Front height L/R Subwoofer
Direct/Pure Direct (2-channel)
S
D
z
3
Direct/Pure Direct (Multi-channel)
S D D
D
z
1 D
z
1
D
Stereo
S D
Multi Ch In
S D D
D
z
1
D
Dolby Pro Logic gz S D D D D
Dolby Pro Logic gx S D D D D
Dolby Pro Logic g S D D D
DTS Neo:6
S D D D D
Dolby Digital
S D D D
D
z
2
D
Dolby Digital Plus
S D D
D
z
1 D
z
1
D
Dolby TrueHD
S D D
D
z
1 D
z
1
D
DTS Surround
S D D D
D
z
2
D
DTS 96/24
S D D D
D
z
2
D
DTS-HD
S D D
D
z
1 D
z
1
D
DTS Express
S D D D
D
z
2
D
Multi Ch Stereo
S D D D D D
S D
z1
A signal for each channel contained in an input signal is output as audio.
z2 Audio is output when the set sound mode name contains “+PLgz”.
z3 Audio is output when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v p. 194)
Contents Connections Playback Settings Tips Appendix
243
Front panel Display Rear panel Remote Index
Sound modes and surround parameters
Sound mode (v p. 118)
Surround Parameter (v
p. 152)
Dialog Level
Adjust
(v
p. 151)
Subwoofer Level
Adjust (v p. 151)
Cinema EQ
(v p. 152)
Loudness
Management
z
1
(v
p. 152)
Dynamic Compression
z
2
(v
p. 153)
Low Frequency
Effects
z
3
(v
p. 153)
Height Gain
z
4
(v
p. 155)
Direct/Pure Direct (2-channel)
z
5
S
z
6
S S
Direct/Pure Direct (Multi-channel)
z
5
S S S S
Stereo
S S S S
Multi Ch In
S S S S S
Dolby Pro Logic gz S S S S S S
Dolby Pro Logic gx S S S S S
Dolby Pro Logic g S S S S S
DTS Neo:6
S S S S S
Dolby Digital
S S S S S S
Dolby Digital Plus
S S S S S S
Dolby TrueHD
S S S S S S S
DTS Surround
S S S S S S
DTS 96/24
S S S S S
DTS-HD
S S S S S
DTS Express
S S S S S
Multi Ch Stereo
S S S S S S
Virtual
S S S S
z
1 -
z
6 : “Sound modes and surround parameters” (v p. 246)
Contents Connections Playback Settings Tips Appendix
244
Front panel Display Rear panel Remote Index
Sound mode (v p. 118)
v
Tone
z
7
(v
p. 114)
Audyssey (v p. 158)
M-DAX
z
10
(v
p. 156)
Pro Logicg/gx Music mode only
Neo: 6 Music
modes only
Panorama
(v p. 154)
Dimension
(v p. 154)
Center Width
(v p. 154)
Center
Image
(v p. 154)
MultEQ
®
XT
z
8 (v p. 158)
Dynamic EQ
z
9
(v p. 159)
Dynamic Volume
z
9 (v p. 160)
Direct/Pure Direct (2-channel)
z
5
Direct/Pure Direct (Multi-channel)
z
5
Stereo
S S S S
Multi Ch In
S S S S
Dolby Pro Logic gz S S S S S
Dolby Pro Logic gx S S S S S S S S
Dolby Pro Logic g S S S S S S S S
DTS Neo:6
S S S S S S
Dolby Digital
S S S S
Dolby Digital Plus
S S S S
Dolby TrueHD
S S S S
DTS Surround
S S S S
DTS 96/24
S S S S
DTS-HD
S S S S
DTS Express
S S S S
Multi Ch Stereo
S S S S S
S S S S S
z
5,
z
7 -
z
10 : “Sound modes and surround parameters” (v p. 246)
Contents Connections Playback Settings Tips Appendix
245
Front panel Display Rear panel Remote Index
z
1
This item can be selected when a Dolby TrueHD signal is played.
z2
This item can be selected when Dolby TrueHD, Dolby Digital or DTS signal is played.
z3
This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
z4 This setting is available when the set sound mode name contains “+PLgz”.
z5
During playback in Pure Direct mode, the surround parameters are the same as in Direct mode.
z6 This setting is available when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v
p. 194)
z7 This item cannot be set when “Dynamic EQ” is set to “On”. (v
p. 159)
z8
This item cannot be set when Audyssey
®
Setup (Speaker Calibration) has not been performed.
z9
This item cannot be set when “MultEQ
®
XT” is set to “Off”. (v p. 158)
z10
This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
z11
In this sound mode, bass is +6 dB, and treble is +4 dB. (Default)
Contents Connections Playback Settings Tips Appendix
246
Front panel Display Rear panel Remote Index
73
To Next Page
Loading...
