Marantz SR7000 - Programming and Using Macros; Macro Programming Steps and Execution; Executing Programmed Macros

3. Press the buttons for the operations you wish to program as a
macro in the sequence you want the macro to progr^ fliem. The
name of the button pressed appears cmi LCD ®. ITie number of
steps in the macro is displayed on LCD © and this number
increases by 1 with each button pressed.
For example, press LD. PLAY,
Each function button can be programmed to perform up to 10
steps in sequence.
* If, while programming, no buttons are pressed for
approximately 1 minute, the remote controller will
automatically return to norma! mode, and no macro will be
programmed in the memory.
4. When you are finished programming macros, use a ballpoint pen
or other sharp point to press the MACRO button III. LCD €> will
display END, and the display will return to normal.
• Macros cannot be programmed for the MODE Q]. MACRO
m, < • ► O, VOL A /T®, MEMO 21 or CLEAR ^ buttons.
In the macro mode it is possible to program the memory to
perform macros containing up to 10 steps.
Each of the function operations (11 including CD, DVD, etc.)
can be used in a macro more than once, however for all
except AMP, only the first function operation will be
transmitted as a signal from the remote controller.
Accordingly, within a single macro, it is not possible to switch
between multiple function operations. (This is to prevent the
switching of the receiver function operation.) Within a macro,
the second lime a function operation is used, it will only be
used on the remote controller itself and no signal will be
transmitted to the component.
EDITING MACROS
Macros may be edited using following procedure,
1. Use a ballpoint pen or other sharp point to press the MACRO
button [Tj until the MACRO and LEARN indicators are displayed
blinking on the LCD,
2. Press the Function button ® to be changed. Let’s use the
example of the laser disc player, by pressing the LD Function
button d],
• LD-M is displayed blinking on LCD
• The number of steps in the completed macro is highlighted
on LCD ©, In this example there are 3 macro programs in
memory.
and the remote controller is ready for macro programming.
3. While pressing the VOL A button [U, use the '' and v Cursor
buttons El to call up the portion of the macro to be changed.
Pressing the button advances through the macro steps and
pressing the v button regresses through the macro steps.
the new step. The old step wiil be erased and rewritten with
the new step.
• To insert a new step in between existing steps in a macro,
after slep 3 press the MEMO button El, then press the button
for the new step. The numbers of the other steps wiil be
adjusted accordingly to accommodate the new step. Since
only 10 steps may be stored in any macro, the tenth step will
be erased if a step is inserted when the total number of steps
is already 10,
- ——— ---^
4
'' . i
• To erase a step in a macro, after step 3 call up the number of
the step to be erased and press the CLEAR button El.
approximately 1 minute, the remote controller will
automatically return to normal mode, and no macro changes
will be programmed in the memory.
4. When you are finished editing macros, use a ballpoint pen or
other sharp point to press the MACRO button d]. END will be
displayed on LCD !§) and the display will return to normal.
USING MACROS
The following procedure will show how to use the function buttons for
which you have programmed macros.
1. Press the Function button i® for the desired macro for 3
seconds. MACRO is displayed on LCD © for approximately 1
second, after which the number of steps in the macro is
displayed on LCD ©.
• The remote controller wiil do nothing if no macros are
programmed. The macro steps are executed in order and the
names of their buttons are displayed on the LCD. Also, the
step numbers displayed on LCD © disappear as each step is
executed.
2. After ail macro commands have been transmitted, the remote
controller returns to normal mode,
• To cancel the transmission of a programmed macro, use the
Cursor buttons El to press a.