EasyManuals Logo

McIntosh C2700 User Manual

McIntosh C2700
32 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
24
Sources however, any Input Source may be assigned
to Mono Mode. To change Stereo Mode to Mono for a
given Input Source, perform the following steps:
Note: The audio signal present at the FIXED OUT
Jacks is affected by the Stereo/Mono setting.
1. Select the desired Input Source.
2. Select “MONO / STEREO,
______
” as
indicated on the Front Panel Information Display.
Refer to figure 78.
3. To select MONO Mode adjust the TRIM LEVEL.
Refer to figure 79.
After approximately 8 seconds the Information
Display returns to indicate the Source Selection and
Volume Level.
METER LIGHTS
The Meter Illumination of McIntosh Power Amplifi-
ers, when connected to the C2700 (refer to pages 7-8),
may be switched On or Off by performing the same
type of operational steps for adjusting the BASS &
TREBLE Tone and MODE Selection:
1. Select “METER LIGHTS, On” as indicated on the
Front Panel Information Display. Refer to figures
60, 63 (on page 22) and 80.
The Front Panel Display indicates the Treble changes
in steps from +12dB to -12dB. After approximately
8 seconds the Display returns to indicate the Source
Selection and Volume Level.
TONE CONTROL
With the Tone Controls On, the TREBLE and
BASS TRIM Settings may be adjusted for the cur-
rently selected Input Source. The LED above the
TONE Push-button will be illuminated. When the
Tone Controls are Off, the previous settings for
Treble and Bass a re by passed f rom the signa l path.
To activate the Tone Controls perform the following:
1. Select the desired Input Source.
2. Press the TRIM Push-button on the Remote Con-
trol until “TONE CONTROLS, On” appears on
the Front Panel Display. Refer to figure 76.
3. Press TRIM LEVEL DOWN Push-button to deac-
tivate the Tone Controls. Refer to figure 77.
After approximately 8 seconds the Display returns to
indicate the Source Selection and Volume Level.
MONO/STEREO MODE
By default the Stereo Mode is active for all Input
Figure 60
How to Operate the C2700, cont
Figure 78
MONO / STEREO
______
Figure 79
MONO / STEREO
____
Figure 74
TREBLE
+12dB
Figure 75
TREBLE
-12dB
Figure 80
METER LIGHTS
On
USB 35%
DSD256
Figure 76
TONE CONTROLS
On
Figure 77
TONE CONTROLS
Off

Table of Contents

Other manuals for McIntosh C2700

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the McIntosh C2700 and is the answer not in the manual?

McIntosh C2700 Specifications

General IconGeneral
Preamplifier TypeVacuum Tube
Number of Channels2
Total Harmonic Distortion0.08%
Signal to Noise Ratio100dB
Outputs3 (2 Balanced + 1 Unbalanced)
High Level Inputs6
Frequency Response20Hz to 20kHz +0, -0.5dB
Digital Audio Inputs2 Optical, 2 Coaxial
Vacuum Tubes6 12AX7A, 2 12AT7
Dimensions17-1/2" (44.45cm) width x 7-5/8" (19.4cm) height x 18" (45.7cm) depth
Rated Output Voltage2.5V Unbalanced, 5V Balanced
Maximum Output Voltage16V Balanced, 8V Unbalanced
Phono Inputs1 MC, 1 MM
Output Impedance100 ohms Unbalanced, 200 ohms Balanced
Headphone OutputYes
TypePreamplifier
Gain15dB (High Level), 40dB (MM), 60dB (MC)

Related product manuals