Home
Megger
Test Equipment
MFT1815
Megger MFT1815 User Manual
4
of 1
of 1 rating
55 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
27
test should not be used on the P-N circuits.
Errors can be r
educed by:-
■
Use the two-wire lead set with pr
ods and making a firm connection to clean conductors.
■
Make several tests and taking the average.
■
Ensure that potential sour
ces of noise in the installation are isolated (switched of
f),
eg: automatically switched loads or motor controllers
26
28
Table of Contents
Default Chapter
2
Table of Contents
2
1 Introduction
6
2 Overview
6
Front Panel and Controls
6
Waste Electrical and Electronic Equipment
8
Battery and Fuse Location, Fitting and Replacement
8
3 Operation
10
General Operation - All Models
10
Mode Button Functions
10
Test Inhibit
11
4 Voltage, Frequency, Current and Temperature Measurement
12
Making a Voltage Measurement
12
5 Continuity / Resistance Measurement
15
Nulling Test Lead Resistance (up to 9.99Ohms) W
15
Making a CONTINUITY Measurement
16
Storing / Downloading Results (MFT1835 Only)
16
Continuity Buzzer ON/OFF
16
Switch Probe (SP5)
17
Buzzer Threshold
17
Measurement Methods and Sources of Error
17
6 Insulation Resistance
18
Making an INSULATION Measurement
18
Insulation Test Lock
18
Measurement Methods and Sources of Error
19
7 Loop Impedance Testing
20
Range Selection and Test Leads
20
Making a Loop Impedance Measurement
22
Phase to Neutral (or Phase to Phase) Testing
25
Prospective Fault Current and Short Circuit Calculation (PFC & PSCC)
26
Measurement Methods and Sources of Error
26
8 Residual Current Device Testing
28
Making an Rcd Measurement
29
Selecting RCD Type
29
RCD Current Rating (No-Trip Test)
29
I RCD Current Rating (Tripping Test on 30Ma RCD)
30
I RCD Current Rating (Tripping Test on 30Ma RCD) - MFT1825 & 1835 ONLY
31
I RCD Current Rating (Tripping Test on 30Ma RCD)
31
Ramp Test
32
Fast Ramp Test
32
Type B (Pure DC) RCD Test
33
Variable Rcds (Not MFT1815)
33
AUTO RCD Testing
34
Phase RCD Testing
34
Touch Voltage Display
35
Measurement Methods and Sources of Error
35
Useful Information
36
9 Earth Resistance Measurement
37
Connection Terminals
37
Touch Voltage Limit
37
Two Terminal Resistance Measurement
37
Three Terminal Resistance Measurement
38
Three Terminal Resistance Measurement Using ART (MFT1825, MFT1835)
39
Two-Clamp Stake-Less Measurement MFT1835 Only
40
10 Setup Options
41
11 Warning Messages
42
Startup Warnings
42
Battery
42
Battery Charger
42
Fuse Warning
42
Invalid Rotary Switch Setting
42
Continuity Test
42
Insulation Test
42
RCD Test
42
RCD Range Selection Errors
42
Loop Test
43
11.11 Earth Test
43
Test will Not Start
43
Appendix A - Sending, Storing, Deleting and Recalling Test Results
44
Appendix B - Downloading Data Using Bluetooth
47
Appendix C - Installation Category Definitions
50
Appendix D - Safe Working Practice
50
Appendix E - Cleaning and Maintenance
50
Appendix F - Earth Resistance Testing - Basic Principles
50
Appendix G - Repair and Warranty
52
General Specification
53
Other manuals for Megger MFT1815
User Guide
70 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Megger MFT1815 and is the answer not in the manual?
Ask a question
Megger MFT1815 Specifications
General
Brand
Megger
Model
MFT1815
Category
Test Equipment
Language
English
Related product manuals
Megger MFT1825
70 pages
Megger MFT1835
70 pages
Megger MFT1800 series
70 pages
Megger MFT1711
4 pages
Megger MFT1710
8 pages
Megger MFT1730
8 pages
Megger MFT1700 series
42 pages
Megger MFT-X1
110 pages
Megger MFT70-US
40 pages
Megger MIT310A
24 pages
Megger MIT1025
32 pages
Megger MIT510/2
14 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
