Need help?Do you have a question about the Megger MFT-X1 and is the answer not in the manual?
Covers essential safety practices for operating the instrument and handling electrical circuits.
Highlights specific warnings and care instructions for Li-ION battery modules.
Explains safety categories (CAT IV, CAT III, CAT II) and voltage ratings based on IEC 61010.
Step-by-step guide for conducting continuity tests and understanding results.
Explains the purpose of insulation resistance tests and the mandatory test start timer.
Details voltage limits that will inhibit insulation testing to prevent hazards.
Step-by-step guide for conducting insulation tests, including test lock functionality.
Details the two-pole measurement method and associated hot keys for earth resistance.
Discusses general procedures, warnings, and risk assessment for live testing.
Details PE confirmation, warnings, and touch voltage checks during live testing.
Explains how to perform single-phase and three-phase voltage measurements.
Introduces RCD testing, supported types, test currents, and general test principles.
Details the ½xI, 1xI, 2xI, 5xI, ramp tests, and phase angle testing.
Explains RCD testing inhibit conditions and customization options.
Introduces Loop Impedance testing, its purpose, and the Confidence Meter.
Explains loop test recommendations and how to measure impedance without RCD protection.
Details how to measure Loop Impedance (Zs) on circuits protected by RCDs.
Explains how to make and use a reference impedance measurement for R1+R2 and Vdrop.
Step-by-step guide for making volt drop measurements using the MFT-X1.
Details continuity buzzer thresholds and live voltage limits for insulation tests.
Configures loop impedance test parameters like polarity, touch voltage, and auto-start.
Configures RCD test parameters like ramp speed, test times, and sequence customization.
Covers essential safety practices for operating the instrument and handling electrical circuits.
Highlights specific warnings and care instructions for Li-ION battery modules.
Explains safety categories (CAT IV, CAT III, CAT II) and voltage ratings based on IEC 61010.
Step-by-step guide for conducting continuity tests and understanding results.
Explains the purpose of insulation resistance tests and the mandatory test start timer.
Details voltage limits that will inhibit insulation testing to prevent hazards.
Step-by-step guide for conducting insulation tests, including test lock functionality.
Details the two-pole measurement method and associated hot keys for earth resistance.
Discusses general procedures, warnings, and risk assessment for live testing.
Details PE confirmation, warnings, and touch voltage checks during live testing.
Explains how to perform single-phase and three-phase voltage measurements.
Introduces RCD testing, supported types, test currents, and general test principles.
Details the ½xI, 1xI, 2xI, 5xI, ramp tests, and phase angle testing.
Explains RCD testing inhibit conditions and customization options.
Introduces Loop Impedance testing, its purpose, and the Confidence Meter.
Explains loop test recommendations and how to measure impedance without RCD protection.
Details how to measure Loop Impedance (Zs) on circuits protected by RCDs.
Explains how to make and use a reference impedance measurement for R1+R2 and Vdrop.
Step-by-step guide for making volt drop measurements using the MFT-X1.
Details continuity buzzer thresholds and live voltage limits for insulation tests.
Configures loop impedance test parameters like polarity, touch voltage, and auto-start.
Configures RCD test parameters like ramp speed, test times, and sequence customization.
General| Power Supply | Rechargeable Li-ion battery |
|---|---|
| Phase Sequence Indication | Yes |
| Resistance Range | 0.01 Ω to 100 kΩ |
| Protection Rating | IP54 |
| Continuity Testing | 0.01 Ω to 2000 Ω |
| Loop Testing | 0.01 Ω to 2000 Ω |
| RCD Testing | Type AC, A, F, B, and B+ |
| Frequency Measurement | 15 Hz to 400 Hz |
| Insulation Test Voltage | 50 V, 100 V, 250 V, 500 V, 1000 V |
| Voltage Range | 12 V to 440 V AC/DC |
| Frequency Range | 15 Hz to 400 Hz |
| Battery Life | Approximately 8 hours |
To Next Page
