MELBOURNE INSTRUMENTS NINA - NINA Knobs

10
MELBOURNE INSTRUMENTS – NINA V 1.3.0
11
MELBOURNE INSTRUMENTS – NINA V 1.3.0
KEY LED STATUS FUNCTION
SOFT KEY 1 ON = key pressed EXIT / BACK / BANK
SOFT KEY 2 ON = mode active EDIT / RENAME
SOFT KEY 3 ON = key pressed SYSTEM / ENTER / SAVE / LOAD / RESET / STORE TO / OK
MOD Blinking = MOD mode active Enter modulation mode
LAYER ON = Layer Menu active Multi-timbral setup and global Preset parameters.
ARP ON = Arpeggiator ON Short Press: turn the Arpeggiator on or o, and display Arp settings.
Long Press: display Arp settings without turning the Arpeggiator on or o.
LOAD ON = Load Menu active Load a Preset onto the current Patch, on the active Layer.
If in LAYER menu, load a Layer setup.
SAVE ON = Save Menu active Save the Patch on the current Layer to a Preset.
If in LAYER menu, save a Layer setup.
A/B OFF = A
ON = B
Switch between the A and B sound of a Preset.
RUN ON = Sequencer running Run the sequencer.
SEQ ON = Sequencer menu active Set up the sequencer
REC ON = Recording sequence Record a sequence
KBD ON = Keyboard On,
display KBD Menu.
Keys 1-16 ON = sharp/at key
Turn Keys 1 to 16 into a built-in keyboard
COARSE ON = Coarse Tune
OFF= Fine Tune
Switch between FINE and COARSE for OSC 1,
OSC 2 & OSC 3 Tune Knobs
SYNC ON = Sync ON
OFF = no sync
Hard Sync VCO 2 to VCO 1
SHAPE ON = Wavetable selection
list active
Select wavetable for OSC 3
LFO 1/2 OFF = LFO 1
ON = LFO 2
Switch LFO RATE, LEVEL, SHAPE controls and LCD menu between LFO
1 and LFO 2
SUB ON = SUB Osc
OFF = Normal Pulse
Switch VCO 1 pulse to sub-octave square
OVERDRIVE ON = Overdrive
OFF = Standard drive
Large boost for very overdriven VCF sound
TYPE (NOISE)
ON = display Type menu
Select White/Pink/Analog XOR or AUX In for the NOISE source
LFO SHAPE
ON = display LFO Shape menu
Select LFO waveform
KEYS 1-16 ON = Item in list / preset
ON = Active step
ON = Active step
ON = Sharps/ Flats
ON = Active MOD Source
LOAD operation: Short-cut to rst 16 Presets or Banks in the list.
SEQ operation: Sequencer position, rests or ties
RUN sequencer: Sequencer step display
KBD Operation: Indicates Sharps/Flats
MOD Mode: Active Modulation Source
NINA Keys NINA Knobs
SECTION LABEL FUNCTION
OSC 1 TUNE Fine tune +/- 7 semitones (1/5).
Coarse Tune +/- 2 octaves.
WIDTH Shape shift from Triangle to Saw.
OSC 2 TUNE FINE & COARSE Tune for Analog VCO 2.
WIDTH Shape shift from Triangle to Saw.
OSC 3 TUNE FINE & COARSE TUNE for Digital OSC 3.
POS Wavetable position for Digital OSC 3.
GLIDE Glissando/Portamento — causes smooth
changes in pitch between notes.
TEMPO Sets the playback speed of arpeggio or sequence.
MIX (OSC 1) BLEND Blend between Pulse and Saw.
OSC 1 Level of OSC 1 into mix.
MIX (OSC 2) BLEND Blend between Pulse and Saw.
OSC 2 Level of OSC 2 into mix.
MIX (OSC 3) OSC 3 Level of OSC 3 into mix.
NOISE Level of Noise/XOR source into mix.
LFO RATE LFO rate control.
LEVEL Set the LFO Level (Gain).
VCF RESONANCE Set the VCF Resonance.
CUTOFF Set VCF Cuto Frequency.
DRIVE Amount of overdrive for smooth distortion control.
EG1 CUT
How much the VCF Envelope (EG1) aects VCF Cuto.
MOD Mode - EG1 Level as Destination.
EG1 AT TACK Set Attack amount for EG1
DECAY Set Decay amount for EG1
SUSTAIN Set Sustain amount for EG1
RELEASE
Set Release amount for EG1
EG2 AT TACK Set Attack amount for EG2
DECAY Set Decay amount for EG2
SUSTAIN Set Sustain amount for EG2
RELEASE
Set Release amount for EG2
OUTPUT MAIN Main/Master level control.
EFFECT / MOD PAN Level of Eects mix in output. Choose type and parameters.
MOD Mode - PAN as Destination.
SPIN Speed control of Stereo Innite Panning Spin.
MORPH / MOD EG2 LVL MORPH all patch parameters between A and B sounds.
MOD Mode - EG2 LVL as Destination.
COMPUTER DATA LCD Navigation / General control access