What to do if the Menvier Security Control Panel display shows 'UNSET AC OFF' and beeps?
This indicates that the mains power to the Menvier Security Control Panel is off, or the internal fuse has blown. The system will operate from the internal battery for about 8 hours. To address this, enter your passcode to silence the beeps. If the mains power to the building is on, contact your alarm company.
Why does the Menvier Security TSD402 Control Panel display 'Au PL TA' and the sounder activate?
This indicates that the Menvier Security Control Panel has detected an Auxiliary or Panel Lid tamper fault, which could be due to a wiring fault or a cover removed from a detector, control panel, or external siren. Enter your passcode to silence the alarm, then call your alarm company immediately.
What to do if Menvier Security TSD402 Control Panel gives an intermittent sound and shows a zone fault when setting?
The tone from the Menvier Security Control Panel indicates that a detector is active or a door has been left open, and the display indicates which detector or door is active. Close any open doors, wait 10 seconds, and try again. If the problem persists, contact your alarm company.
Why does the outside strobe flash when setting the Menvier Security TSD402 system?
This indicates that the Menvier Security Control Panel system has failed to set correctly. Re-enter the building and enter your passcode to unset the system. Check that all doors and windows are closed, and try again.
What to do if Menvier Security Control Panel shows an alarm code and beeps after entering the passcode?
The indication on the Menvier Security Control Panel display shows the alarm zone that was activated when the system was set. Check the building for signs of a break in, then refer to the section on Resetting after an Alarm.
Why does the external siren pulse when the Menvier Security Control Panel alarm is activated?
The TSD402 Menvier Security Control Panel has a facility to monitor smoke detectors. If one of these is activated, the external siren will pulse to show that the alarm was caused by a fire and not a burglar. Check the smoke detector to ensure that they are clear of smoke. If the problem persists contact your alarm company.
How to fix Menvier Security TSD402 Control Panel when it won't allow me to change my passcode?
The TSD402 Menvier Security Control Panel analyses the new code entered and may refuse to accept certain code combinations for technical reasons. Try repeating the procedure with a different passcode.
Why does my Menvier Security TSD402 Control Panel beep when I open doors or walk in front of detectors?
The TSD402 Menvier Security Control Panel has a facility called CHIME, which generates a two-tone sound from the control panel every time certain zones are activated. To turn this facility on or off, see the section on Changing Chime Zones.
What does 'NO REPLY' mean on the Menvier Security TSD402 when sending a test call?
The call was not answered or acknowledged by the recipient. Ring the recipient and check they have followed the call acknowledgement procedure.
What does 'UNOBTAINABLE' mean on the Menvier Security TSD402 when sending a test call?
The TSD402 Menvier Security Control Panel has dialled the number and detected something other than a `ringing' or `engaged' tone (e.g., a B.T. or Cellnet recorded message). Check the number using a normal telephone or try again.
Procedure for arming the system in the 'Away' mode for complete security.
Procedure for arming the system in the 'Home' mode for partial security.
Procedure to disarm the alarm system via the entry route.
Steps to reset the system following an alarm activation.
Allows User 1 to change their personal passcode.
Accesses the menu for programming speech dialler settings.
How to record custom voice messages for alarm calls.
Common problems and solutions for the alarm system's operation.
Common problems and solutions specific to the speech dialler function.
General| Part No | TSD402 |
|---|---|
| Frequency | 50Hz |
| Input Voltage | 230V AC |
| Outputs | 2 |
| Operating Temperature | -10°C to +50°C |
To Next Page
