31
SPECIFICATIONS OF THE MAIN UNIT
Item CG-60ST
Acceptable sheet width 50 to 711mm (Roll sheet : 50 to 670mm)
Effective cutting area (note 1) 586mm x 51 m (Normal ) 606 mm x 51 m (Expand)
Maximum cutting speed 50 cm/s
Speed setting 1 to 10 cm/s (in 1 cm/s steps)
(cutting/plotting) 10 to 50 cm/s (in 5 cm/s steps)
Mechanical resolution 5 µm
Program steps 25 µm, 10 µm
Repeatability ± 0.2 mm (excluding expansion/contraction due to film temperatures)
Maximum pressure 300 g
Pressure setting Cutter 10 ~ 20 g (2 g step), 20 ~ 100 g (5 g step), 100 ~ 300 g (10 g step)
Pen 10 ~ 20 g (2 g step), 20 ~ 100 g (5 g step), 100 ~ 150 g (10 g step)
Acceptable films PVC sheets (0.15 mm thick or less), fluorescent sheets, reflective sheets (note 2)
Applicable tools Cutters, water-ink ball-point pens and oil-ink ball-point pens,Ball-point pen on the market.*3
Commands MGL-IIc2
Interface RS-232C, 8-bit parallel
Receiver buffer 2 MB standard
Operating environment 5 to 35°C, 35 to 75 % (Rh) Non-condensing
Power capacity AC100-240 V, 1A or less
Outside dimensions Wide 875 mm
Depth 385 mm
Hight 315 mm
Weight 16 kg
•Notes Refer to the next page for the explanation of notes 1 to 3.
*1: Maximum feed length has a limitation depending on the software you use.
*2: When reflection sheet is used, use special blades (special blade for fluorescent sheet (SPB-0007), special
blade for reflection sheet (SPB-0006)) which are available as optional items.
*3: As for the ball-point pen on the market, use the ones with 8mm~9mm diameter. Pen tip position may vary
depending on the pen. Picture quality may also vary depending on the pen.
Option
Description Code Remarks Suitable media Offset [mm] Pressure [g] Speed [cm]
General vinyl use SPB-0030 Standard accessory. 3 PCs/set. Vinyl sheet. 0.3 20-100 20-40
for low pressure Use to cut thin backing sheet. Thickness from
Less than 100g pressure. 0.05mm to 0.1mm
Cutting quality will be improved because of low
pressure setting.
General vinyl use SPB-0001 3 pcs/set Use to cut general vinyl sheet Vinyl sheet. Thickness 0.3 100-150 20-40
from 0.05 mm to 0.1 mm
50-100 20-40
Small characters SPB-0003 3 pcs/set Use to cut sharp small characters. Vinyl sheet. Thickness 0.15 50-100 20-40
Not suitable to cut thick sheet.
from 0.05 mm to 0.1 mm
40-80 20-40
For rubber sheet SPB-0005 3 pcs/set. Use to cut rubber sheet less than 0.8mm Rubber sheet less 0.75 200-300 5-20
than 0.8 mm
For reflective sheet SPB-0006 2 pcs/set. Long lifetime due to Titanium Coated. Engineering grade & 0.75 250-400 5-15
Also for Polyester film Polyester film less 200-300 5-20
than 0.01 mm
For fluorescent sheet SPB-0007 3 pcs/set Fluorescent sheet 0.5 150-200 10-20
Cutter Holder SPA-0001 1pc without blade
Protrusion Adjustment OPT-S1005 Optical type for SPA-0001
To Next Page
Loading...
Need help?
General
