Minolta A2 User Manual

(2720)A 23
REPAIR GUIDE
AA
AA
A
Fig.1 Installation of the 1st lens group moving barrelFig.1 Installation of the 1st lens group moving barrel
Fig.1 Installation of the 1st lens group moving barrelFig.1 Installation of the 1st lens group moving barrel
Fig.1 Installation of the 1st lens group moving barrel
The stopper of the hood valve on the 1st lens group moving barrel should be in the position shown on theThe stopper of the hood valve on the 1st lens group moving barrel should be in the position shown on the
The stopper of the hood valve on the 1st lens group moving barrel should be in the position shown on theThe stopper of the hood valve on the 1st lens group moving barrel should be in the position shown on the
The stopper of the hood valve on the 1st lens group moving barrel should be in the position shown on the
figure. Insert it into the lead.figure. Insert it into the lead.
figure. Insert it into the lead.figure. Insert it into the lead.
figure. Insert it into the lead.
NotchNotch
NotchNotch
Notch
1st lens group guide pin-B1st lens group guide pin-B
1st lens group guide pin-B1st lens group guide pin-B
1st lens group guide pin-B
StopperStopper
StopperStopper
Stopper
LeadLead
LeadLead
Lead
Fig.2 Installation of the outer barrel assyFig.2 Installation of the outer barrel assy
Fig.2 Installation of the outer barrel assyFig.2 Installation of the outer barrel assy
Fig.2 Installation of the outer barrel assy
1. Set it to let the mark of the zoom encoder1. Set it to let the mark of the zoom encoder
1. Set it to let the mark of the zoom encoder1. Set it to let the mark of the zoom encoder
1. Set it to let the mark of the zoom encoder
gear be in the range of A part.gear be in the range of A part.
gear be in the range of A part.gear be in the range of A part.
gear be in the range of A part.
MarkMark
MarkMark
Mark
Zoom encoder gearZoom encoder gear
Zoom encoder gearZoom encoder gear
Zoom encoder gear
2. Turn back the zoom cam barrel slightly from 2. Turn back the zoom cam barrel slightly from
2. Turn back the zoom cam barrel slightly from 2. Turn back the zoom cam barrel slightly from
2. Turn back the zoom cam barrel slightly from
the end of "Wide" angle position to let it bethe end of "Wide" angle position to let it be
the end of "Wide" angle position to let it bethe end of "Wide" angle position to let it be
the end of "Wide" angle position to let it be
in the position where the notch of the fixin the position where the notch of the fix
in the position where the notch of the fixin the position where the notch of the fix
in the position where the notch of the fix
barrel and the zoom cam barrel are aligned.barrel and the zoom cam barrel are aligned.
barrel and the zoom cam barrel are aligned.barrel and the zoom cam barrel are aligned.
barrel and the zoom cam barrel are aligned.
3. Turn the 1st lens moving barrel down into it.3. Turn the 1st lens moving barrel down into it.
3. Turn the 1st lens moving barrel down into it.3. Turn the 1st lens moving barrel down into it.
3. Turn the 1st lens moving barrel down into it.
NotchNotch
NotchNotch
Notch
Fix barrelFix barrel
Fix barrelFix barrel
Fix barrel
Zoom cam barrelZoom cam barrel
Zoom cam barrelZoom cam barrel
Zoom cam barrel
1st lens group1st lens group
1st lens group1st lens group
1st lens group
moving barrelmoving barrel
moving barrelmoving barrel
moving barrel
4. Install the outer barrel assy to insert the cam4. Install the outer barrel assy to insert the cam
4. Install the outer barrel assy to insert the cam4. Install the outer barrel assy to insert the cam
4. Install the outer barrel assy to insert the cam
connection lever into the notch of the zoom camconnection lever into the notch of the zoom cam
connection lever into the notch of the zoom camconnection lever into the notch of the zoom cam
connection lever into the notch of the zoom cam
barrel (two parts).barrel (two parts).
barrel (two parts).barrel (two parts).
barrel (two parts).
Cam connection leverCam connection lever
Cam connection leverCam connection lever
Cam connection lever
NotchNotch
NotchNotch
Notch

Minolta A2 Specifications

General

Sensor Type	CCD
Optical Zoom	7x
Display Size	1.8 inches
ISO Sensitivity	64 - 800
Image Stabilization	No
Max Resolution	3264 x 2448
Image Ratio w:h	4:3
Sensor Size	2/3" (8.8 x 6.6 mm)
Maximum Aperture	F2.8 - F3.5
Storage Types	CompactFlash (Type I or II), Microdrive
Viewfinder	Electronic
Resolution	8 megapixels
Lens Focal Length	28 - 200 mm
Battery	NP-400 Lithium-Ion rechargeable battery
Shutter Speed	30 - 1/4000 sec