Mitsubishi Electric MELSERVO-J4 MR-J4 A Series - Page 199

6. NORMAL GAIN ADJUSTMENT
6 - 12
(f) If a warning occur
ࡢࡦ࠲࠶࠴⺞ᢛߦ⼊๔߇⊒↢ߒߚ႐ว㧘ࠕ࡜࡯ࡓ⴫␜ߦㆫ⒖ߒ㧘⼊๔ࠍ⴫␜ߒ߹ߔޕ
ߎߩߣ߈ㆇォ߇⛮⛯ߢ߈ࠆ⼊๔ߩ႐วߪࡢࡦ࠲࠶࠴⺞ᢛࠍ⛮⛯ߒߡታᣉߒ߹ߔޕ
ࡢࡦ࠲࠶࠴⺞ᢛ
ࠕ࡜࡯ࡓ⴫␜⼊๔
(g) Clearing one-touch tuning
Refer to table 6.1 for the parameters which you can clear.
You can initialize the parameters changed by the one-touch tuning with the clear mode. You can
reset the parameters to before tuning with the back mode.
1) Push the "MODE" button to switch to the initial screen ("AUTO") of the one-touch tuning.
2) Select the clear mode or back mode with the "UP" or "DOWN" button.
ࡢࡦ࠲࠶࠴⺞ᢛࠢ࡝ࠕࡕ࡯࠼ㆬᛯ
DOWNUP
"SET"ࡏ࠲ࡦࠍ2sએ᛼ߔߣ㧘ࡢࡦ࠲࠶࠴⺞ᢛߩࠢ࡝ࠕࠍታᣉߒ߹ߔޕ
ㆬᛯߒߚࡢࡦ࠲࠶࠴⺞ᢛࠢ࡝ࠕࡕ࡯࠼ࠍታᣉߒ߹ߔޕታᣉ㧘ࡢࡦ࠲࠶࠴⺞ᢛࠢ࡝ࠕࡕ࡯
࠼
ߩࠪࡦࡏ࡞߇3sὐṌߒ߹ߔޕ
ࡢࡦ࠲࠶࠴⺞ᢛࠢ࡝ࠕ߇ቢߔࠆߣ㧘ೋᦼ↹㕙ߦㆫ⒖ߒ߹ߔޕ
ࡢࡦ࠲࠶࠴⺞ᢛࠢ࡝ࠕࡕ࡯࠼⴫␜(ೋᦼ୯ߦᚯߔ႐ว)
ೋᦼ↹㕙
ࠝ࡯࠻ࡕ࡯࠼
ࠢ࡝ࠕࡕ࡯࠼
ࡃ࠶ࠢࡕ࡯࠼
One-touch tuning in progress
A
larm display (warning)
If a warning occurs during tuning, the alarm No. of the warning will be displayed.
When the warning is one which continue the motor driving, the one-touch tuning will be
continued.
One-touch tuning clear mode selection
Clear mode
Back mode
A
uto mode
To clear the one-touch tuning, push the "SET" button for 2 s.
One-touch tuning clear mode display (initializing)
The one-touch tuning clear mode is in progress.
The clear mode symbol flickers for 3 s.
Clearing one-touch tuning is completed, the initial screen will be displayed.
Initial screen