Mitsubishi Electric Q26UD(E)HCPU - Page 349

347
APPENDICES
A
Appendix 1 Error Codes Appendix 1.4 List of error codes (2000 to 2999)
2230
[RESTORE ERROR]
• The system file does not exist in the backup
data to be restored.
• File(s) in the system file information does not
exist in the folder of the backed up data.
■Collateral information
• Common information: -
• Individual information: -
■Diagnostic timing
• At power-on/At reset
Restore with any other backup data because
the backup data may have been corrupted.
RUN: Off
ERR.:Flashing
CPU Status:Stop
QnUDV
2231
[RESTORE ERROR]
The data which is same as the one set the file
password 32 is restored to the restoration
destination CPU module.
■Collateral information
• Common information: -
• Individual information: -
■Diagnostic timing
• At power-on/At reset
To use the CPU module data
backup/restoration function, delete the file
password 32 setting and then execute the
function.
RUN: Off
ERR.:Flashing
CPU Status:Stop
QnUDV
2232
[RESTORE ERROR]
• The folder with the setting values of SD919 to
SD921 (Restoration target folder) does not exist
in the SD memory card.
• The setting value of SD917 (Restoration target
data setting) is out of range.
■Collateral information
• Common information: -
• Individual information: -
■Diagnostic timing
• At power-on/At reset
• Check and correct the setting value of
SD919 to SD921 (Restoration target
folder), and then execute the processing
again.
• Check and correct the setting value of
SD917 (Restoration target data setting)
and execute the processing again.
RUN: Off
ERR.:Flashing
CPU Status:Stop
QnUDV
2233
[RESTORE ERROR]
Automatic restoration is executed while no SD
memory card is inserted.
■Collateral information
• Common information: -
• Individual information: -
■Diagnostic timing
• At power-on/At reset
Insert or re-insert the SD memory card and
then execute the processing again.
RUN: Off
ERR.:Flashing
CPU Status:Stop
QnUDV
2234
[RESTORE ERROR]
• Automatic restoration is executed while the
memory size exceeds the maximum capacity of
the CPU module.
• Automatic restoration is executed while the
number of files exceeds the number of storable
files of the CPU module.
■Collateral information
• Common information: -
• Individual information: -
■Diagnostic timing
• At power-on/At reset
• Check the size of restoration target data so
that it will not be larger than the memory
capacity, and execute the processing
again.
• Check the number of files so that it will not
exceed the number of storable files, and
execute the processing again.
RUN: Off
ERR.:Flashing
CPU Status:Stop
QnUDV
22
35
[RESTORE ERROR]
The CPU module status (such as programs,
parameters, and file structure) of restoration
destination is different from the status at the time
of backup.
■Collateral information
• Common information: -
• Individual information: -
■Diagnostic timing
• At power-on/At reset
• Restore the data with the CPU module
status at the time of backup.
• Set SD917 (Restoration target data setting)
to all the target data of backup and
restoration and then restore the data.
RUN: Off
ERR.:Flashing
CPU Status:Stop
QnUDV
2240
[LOAD ERROR]
The model of the load-destination CPU module is
different from that of the load-source CPU module.
■Collateral information
• Common information: -
• Individual information: -
■Diagnostic timing
• At power-on/At reset
Execute auto loading using the same model
as that of the load-source CPU module.
RUN: Off
ERR.:Flashing
CPU Status:Stop
LCPU
Error
code
Error and cause Corrective action
LED status,
CPU status
Corresponding
CPU