68
Main Unit Specifications
MDX-20 MDX-15
XY table size
220 mm (X) x 160 mm (Y) ( 8-5/8 in. x 6-1/4 in. )
170 mm (X) x 110 mm (Y) ( 6-11/16 in. x 4-5/16 in. )
Max. operation area 203.2 mm (X) x 152.4 mm (Y) x 60.5 mm (Z) 152.4 mm (X) x 101.6 mm (Y) x 60.5 mm (Z)
(8 in. (X) x 6 in. (Y) x 2-3/8 in. (Z)) (6 in. (X) x 4 in. (Y) x 2-3/8 in. (Z))
Max. table load weight 1000 g (2.2 lb.) 500 g (1.1 lb.)
Interface Serial (RS-232C)
Control keys STANDBY key, VIEW key, TOOL-UP key, TOOL-DOWN key,
LED SCANNING MODE LED, MODELING MODE LED, VIEW LED
Power consumption
Exclusive AC adapter (DC+19V 2.1 A)
Acoustic noise level Standby mode : under 35 dB (A)
Operation mode (not cutting) : under 70 dB (A) (According to ISO 7779)
External dimensions 476.8 mm (W) x 381.6 mm (D) x 305 mm (H) 426 mm (W) x 280 mm (D) x 305 mm (H)
(18-13/16 in. (W) x 15-1/16 in. (D) x 12-1/16 in. (H)) (16-13/16 in. (W) x 11-1/16 in. (D) x 12-1/16 in. (H))
Weight (unit only) 13.7 kg (30.2 lb.) 9.6 kg (21.2 lb.)
Operation temperature 5 to 40°C (41 to 104°F)
Operation humidity 35 to 80 % (no condensation)
Accessories
AC adapter: 1, power code: 1, Roland Software Package CD-ROM: 1, spindle unit: 1, sensor unit: 1, cap
screw M4x15: 4, tool:1, set screw M3x3: 2, double-sided tape: 1, front cover: 1, hexagonal wrench (size :
3 mm) :1, hexagonal wrench (size : 1.5 mm): 1 positioning pins: 3, clay: 1, MDX-20/15 user's manual: 1
Modeling Functions
Tool chuck : 6 mm or 1/8 in. tool chuck included
Spindle motor : 10W (DC motor)
Software resolution : 0.025 mm/step (0.000984 in./step)
Mechanical resolution : 0.00625 mm/step (0.000246 in./step)
Revolution speed : 6500 rpm
Feed rate : 0.1 to 15 mm/sec. (0.00393 to 9/16 in./sec.)
Acceptable material : Wood, Plaster, Resin (modeling wax, styrenform), Chemical wood, Aluminum (A5052 according to JIS),
Brass
Acceptable tool : Endmill, Drill
Scanning Functions
Sensor : Roland Active Piezo Sensor (R.A.P.S.)
Probe length 60 mm (2-5/16 in.), tip bulb diameter 0.08 mm
(0.00315
in.
)
Scanning method : Contacting, mesh-point height-sensing
Scanning pitch : X/Y-axis directions -- 0.05 to 5.00 mm (0.002 to 0.20 in.) (settable in steps of 0.05 mm (0.002 in.))
(Dr. PICZA) Z-axis direction -- 0.025 mm (0.000984 in.)
Scanning speed : 4 to 15 mm/sec. (1/8 to 9/16 in./sec.)
Interface Specification
[Serial]
Standard : RS-232C specifications
Transmission method : Asynchronous, duplex data transmission
Transmission speed : 9600 bps
Parity Check : None
Data Bits : 8 bits
Stop Bits : 1 bits
Handshake : Hardware
12 Specifications
To Next Page
Loading...