Motorola PTP 500 Series - Figure 51 - Reset Configuration and Reboot Confirmation Pop-Up

To Next Page

To Previous Page

7 Web Page Reference

Figure 51 - Reset Configuration and Reboot Confirmation Pop-up

On confirmation the PTP 500 Series Bridge will:

• Upload the configuration file

• Perform data integrity checking

• Erase previous configuration

• Apply the new configuration

• Restart

After the unit has restarted the entire configuration from the configuration file will now be

active. The IP address of the unit may have also been changed. The user can check the new

IP address by reading the header of the configuration file, Figure 49.

CAUTION

A reboot is always required to restore a configuration file.

Main Page

Default Chapter2
- Copyright Information2
- Table of Contents3
1 About this User Guide21
- Who Should Use this Guide21
- Contact Information22
- Interpreting Typeface and Other Conventions22
  - Fonts22
  - Table 1 - Contact Information22
- Table 2 - Font Types22
- Terminology23
- Warnings, Cautions and Notes23
- Getting Additional Help24
- Repair and Service24
- Electrical Safety25
- Warranty25
- RF Safety27
- Compliance with Regulations30
2 Product Description32
- Product Function32
- Typical Deployment33
- Figure 1 - Typical PTP 500 Series Bridge Deployment33
- Frequency Variants34
- Other Product Variants34
- Network Connection34
- Table 4 - PTP 500 Series Bridge Frequency Variants34
- Outdoor Unit (ODU)35
- Figure 2 - PTP 500 Series Bridge Outdoor Unit (ODU)35
- PIDU Plus PTP 300/500/600 Series36
  - Power and Ethernet Leds36
  - Figure 3 - Power Indoor Unit (PIDU Plus PTP 300/500/600 Series)36
  - ODU, LAN and Recovery37
  - DC in and out37
  - Remote Connectors and Jumpers37
  - Figure 4 - PIDU Plus Recovery Switch Location37
  - Mains Connection38
- Redundancy and Alternative Powering Configurations38
- Figure 5 - PIDU Plus Power Input38
- Figure 6 - External DC Supply Only39
- Figure 7 - External DC Supply and AC Supply39
- Figure 8 - External DC Supply and Redundant AC Supply39
- Remote Leds and Recovery Switch40
- Cables and Connectors40
- Figure 9 - Remote LED and Recovery Switch Wiring40
- PTP and Lightning Protection41
- Mounting Brackets42
3 Product Features43
- Ethernet Frames43
- Management Function44
- Configuration and Management44
- Figure 10 - PTP 500 Series Bridge Layer Diagram44
- Channel Bandwidth and Link Symmetry Control45
- Non Line of Sight (NLOS) and Line of Sight (LOS)45
- Upgradeable Software45
- Networking Information45
- Link Mode Optimization46
  - IP Link Mode Optimization46
  - TDM Link Mode Optimization46
- Telecoms Circuits47
- Radar Avoidance48
4 Planning Considerations49
- Spectrum Planning49
  - Regions Without Mandatory Radar Detection49
  - Regions with Mandatory Radar Detection50
- Licenses and Region Codes50
- Radar Avoidance and Bandwidth Operation51
- Figure 11 - 5.8 Ghz UK RTTT Channel Avoidance - 15 Mhz Channel Bandwidth (Example)51
- Variable Channel Bandwidth Operation52
- Link Planning52
- Site Selection Criteria54
  - ODU Site Selection54
  - PIDU Plus Site Selection54
- Wind Loading54
- Path Loss Considerations57
  - Calculating Path Loss57
  - Adaptive Modulation57
- System Threshold, Output Power and Link Loss58
5 Lightning Protection59
- Lightning Protection Zones59
- Figure 12 - ODU Mounted in Zones a & B60
- Figure 13 - Using a Finial to Extend Zone B61
- LPU Detailed Installation62
- Figure 14 - PTP LPU Installation Example for PTP 500 Series (Not to Scale)62
- LPU Kit63
- LPU Installation Wiring63
- Figure 15 - PTP LPU Full Kit63
- Figure 16 - Simplified Circuit Diagram64
- LPU Installation Diagram65
  - Typical Mast or Wall Installation66
  - Figure 17 - Typical Mast or Wall Installations66
6 Installation67
- Installation Support68
- Legal Disclaimer68
- Preparation68
  - Checks68
  - Tools Required68
- Mounting the Odus69
- Connecting up73
- Establishing a Radio Link86
7 Web91
- Menu Navigation Bar91
- Figure 35 - Menu Navigation Bar92
- Home (System Summary)93
  - Figure 36 - System Summary Page93
  - Figure 37 - Alarm Warning Triangle94
  - Home Page Alarm Display94
  - System Alarms95
  - Table 8 - Telecoms Channel Status Alarm Conditions95
- System Status98
  - Figure 38 - Status Page98
  - Histogram Data102
- System Administration103
- Figure 39 - System Administration Login Page103
- Configuration104
  - System Configuration104
  - Figure 40 - System Configuration Page104
  - LAN Configuration106
  - Figure 41 - LAN Configuration Page106
  - Figure 42 - Configuration Reboot Page108
  - Figure 43 - Configuration Reboot Page - Ethernet Auto Negotiation Disabled108
  - Figure 44 - VLAN Configuration Fields109
  - Figure 45 - LAN Configuration Page - Manual Ethernet Configuration110
  - Qos Configuration Page111
  - Figure 46 - Qos Configuration Page111
  - Table 9 - Qos Default Settings111
  - Table 10 - Classification Rules Upgrade Example112
  - Table 11 - IEEE802.1Q Classification Rules112
  - Save and Restore113
  - Figure 47 - Save and Restore Configuration Page113
  - Figure 48 - Save Configuration File Screen114
  - Figure 49 - PTP 500 Example Configuration File114
  - Figure 50 - Restore Configuration File Pop up Screen115
  - Figure 51 - Reset Configuration and Reboot Confirmation Pop-Up116
  - Telecoms Configuration117
  - Figure 52 - Telecoms Data Entry117
- Statistics119
  - Figure 53 - System Statistics Page119
  - Detailed Counters122
  - Figure 54 - Detailed Counters Page122
- Installation Wizard124
  - Factory Configuration124
  - Table 12 - PTP 500 Series Bridge Factory Configuration Values125
  - Manual Configuration126
  - Figure 55 - License Key Data Entry126
  - Installation Wizard Step 1 - Interface Configuration127
  - Figure 56 - Installation Wizard Internet Protocol Configuration127
  - Figure 57 - VLAN Warning128
  - Figure 58 - Telecoms Configuration Interface129
  - Installation Wizard Step 2 - Wireless Configuration131
  - Figure 59 -Wireless Configuration131
  - Figure 60 - Fixed Frequency Configuration Example134
  - Installation Wizard Step 3 - Confirm Configuration135
  - Figure 61 - Installation Wizard Confirm Configuration135
  - Figure 62 - Reboot Confirmation Pop up136
  - Disarm Installation137
  - Figure 63 - Disarm Installation137
  - Figure 64 - Optional Post Disarm Configuration138
  - Graphical Install139
  - Figure 65 - Graphical Installation Screen139
- Software Upgrade140
  - Figure 66 - Software Upgrade140
  - Figure 67 - Software Upgrade Image Check141
  - Locate and Upload Software Image141
  - Figure 68 - Software Download Progress Indicator142
  - Program Software Image into Memory142
  - Software Upgrade Complete142
  - Figure 69 - Software Upgrade Complete Page143
  - Figure 70 - Reboot Confirmation Pop up143
  - Reboot after Software Upgrade143
- Spectrum Management144
  - Wireless Channels144
  - Spectrum Management Measurements144
  - Measurement Analysis145
  - The Spectrum Management Master / Slave Relationship146
  - Figure 71 - Spectrum Management as Seen from the Master147
  - Figure 72 - Spectrum Management as Seen from the Slave148
  - Spectrum Management Configuration149
  - Barring Channels150
  - Master and Slave Channel Spectrum Graphics150
  - Table 13 - Spectrum Management Change State Key151
  - Active Channel History152
  - Figure 73 - Active Channel History Screen152
  - Viewing Historic Spectrum Management Metrics153
  - Figure 74 - Spectrum Management Time Series Plot153
  - Table 14 - Spectrum Management Time Series Key153
  - Spectrum Management (Fixed Frequency)154
  - Figure 75 - Spectrum Management Fixed Frequency Screen154
  - Figure 76 - Spectrum Management Help Page (Fixed Frequency)155
  - Spectrum Management Control with Radar Avoidance156
  - Figure 77 - Spectrum Management Master Screen with Operational Restrictions156
  - Figure 78 - Spectrum Management Slave Screen with Operational Restrictions157
  - Table 15 - Spectrum Management Change State Key with Operational Restrictions157
- Remote Management158
  - Figure 79 - Remote Management158
  - Control Access to HTTP Interface159
  - Control Access to Telnet Interface159
  - SNMP (Simple Network Management Protocol)159
  - Supported Management Information Bases (MIBS)159
  - Figure 80 - Warning When Disabling HTTP Interface160
  - Diagnostics Alarms161
  - Figure 81 - Remote Management - Diagnostic Alarms161
  - SNMP Configuration161
  - SMTP (Simple Mail Transport Protocol)162
  - Setting the Clock163
  - SNTP (Simple Network Time Protocol)163
- Diagnostics Plotter164
  - Diagnostic Plotter Page165
  - Figure 82 - Diagnostic Plotter165
  - CSV Download166
  - Figure 83 - CSV Download166
- Change Password167
- License Key167
- Figure 84 - Password Change167
- Figure 85 - Software License Key Data Entry167
- Figure 86 - License Key Reboot Screen168
- Figure 87 - Reboot Confirmation Pop up168
- Properties169
- Figure 88 - Properties169
- Reboot170
- Figure 89 - System Reboot170
- Figure 90 - Reboot Confirmation Pop up170
8 Recovery Mode171
- Entering Recovery Mode171
- Figure 91 - Recovery Mode Warning Page171
- Figure 92 - Recovery Options Page172
- Upgrade Software Image173
- Figure 93 - Software Download Progress Indicator Page173
- Figure 94 - Software Download Complete Page173
- Figure 95 - Reboot Confirmation Pop up174
- Reset IP & Ethernet Configuration175
- Figure 96 - Confirm Reset to Factory Default Pop up175
- Figure 97 - IP and Ethernet Erased Successfully Page175
- Erase Configuration176
- Figure 98 - Reboot Confirmation Pop up176
- Figure 99 - Confirm Erase Configuration Pop up176
- Figure 100 - Erase Configuration Successful Page177
- Figure 101 - Erase Configuration - Reboot Confirmation Pop up177
- Erase Security Parameters178
- Figure 102 - Confirm Zeroise Security Parameters Pop up178
- Figure 103 - Zeroise Security Parameters Successful Page179
- Reboot180
- Figure 104 - Recovery - Reboot Confirmation Pop up180
9 Troubleshooting (Fault Finding)181
- Test Link End Hardware181
- Test Radio Link188
  - No Activity188
  - Some Activity189
- Lightning Strike189
10 Connectorized PTP 500 Series Bridge190
- Product Description190
- Software/Features191
- Deployment Considerations196
- Link Budget196
- Regulatory Issues with Connectorized Units196
  - Cable Losses (FCC Regions Only)197
- Antenna Choices197
- Table 17 - Cable Losses Per Length197
- Installation198
- Additional Lightning Protection203
11 E1/T1 Installation Guide205
- E1/T1 Cable Assembly205
  - T568B Color Coding205
  - Figure 118 - RJ45 Pin Connection (T568B Color Coding)205
- Connecting the E1/T1 Cable to the PIDU Plus206
- Testing the E1/T1 Installation208
12 Data Rate Calculations209
- Data Rate Defined209
- Calculation Procedure and Example209
  - Procedure209
  - Example210
- Data Throughput Capacity211
- Table 19 - Data Throughput for PTP 500, Link Symmetry = Adaptive or 3:1212
- Table 20 - Data Throughput for PTP 500, Link Symmetry = 1:1, Link Optimization = IP213
- Range Adjustment Curves214
- Table 21 - Data Throughput for PTP 500, Link Symmetry = 1:1, Link Optimization = TDM214
- Figure 120 - PTP 500 Range Adjustment for Data Rates, Curve a215
- Figure 121 - PTP 500 Range Adjustment for Data Rates, Curve B216
13 AES Encryption217
- Encryption Standard Used217
- Upgrading for Link Encryption217
- Configuring Link Encryption217
- Wireless Link Encryption FAQ221
14 Remote Software Upgrade by TFTP222
15 Legal Notices224
- Motorola Inc. End User License Agreement224
- Hardware Warranty in U.S233
- Limit of Liability233
16 PTP 500 Reference Information234
- PTP 500 General Reference Information234
- PTP 54500 Reference Information239
- PTP 58500 Reference Information256
17 Faqs278
18 Glossary280
Index281

Motorola PTP 500 Series - Figure 51 - Reset Configuration and Reboot Confirmation Pop-Up

Table of Contents

Related product manuals