ROYAL SX
22
10. Switching on, using the
transmitter
!
The ROYAL SX is supplied with the transmitter
battery partially charged. The pack must be fully
charged before you use the transmitter. Please refer
to the charging notes ( 8.).
10.1. Switching on for the first time
The very first time you switch the ROYAL SX trans-
mitter on is a special case. When switched on, the
transmitter displays the following menu:
ROYAL SX16 3.46 DE/EN
Select language:
Sprache wählen:
skip/später
English
Deutsch ENTER ▲
In this menu you select the language which the trans-
mitter will use for the menus and the names of the
pre-defined mixers and assignment lists. We recom-
mend that you select the appropriate language when
you first switch the transmitter on:
Select the appropriate language using the ▲ and ▼
buttons, then press ENTER to confirm your choice.
If you select English:
a. English will be used as the menu language.
b. The pre-defined mixers are defined using English
terminology:
ELEVATR+, AILERON+, …
The mixer inputs are also described in English:
Aileron, Elevator, Rudder, …
If you change the selected language to German
(Deutsch) in the menu Setup, User, then the
names of the pre-defined mixers will continue to
appear in English, but the German terms will be
used for the mixer inputs:
Quer, Höhe, Seite, …
It is possible to change the names of all the four-
teen free mixers to anything you like (Name pa-
rameter). This is accomplished in the menu Setup,
Mixer def..
If you select Deutsch (German):
a. German will be used as the menu language.
b. The pre-defined mixers are defined using the
German terminology:
HÖHE+, QUER+, …
The mixer inputs are also described in German:
Quer, Höhe, Seite, …
If you select skip/später (not recommended):
a. English will be used as the language.
b. Next time you switch on, the same menu will ap-
pear, and you can repeat the language selection.
10.2. Normal Operations
This is the procedure for operating your ROYALevo,
ROYAL SX or ROYAL SX M-LINK transmitter in nor-
mal mode:
1. Switch the ROYALevo, ROYAL SX or ROYAL SX
M-LINK transmitter ON:
The red LED on the transmitter flashes once
every two seconds.
2. Switch the M-LINK receiver ON.
The M-LINK system is now ready for use.
10.3. RF module excl. Scanner installed
The 2.4 GHz ISM band offers the facility to transmit
model data back to the transmitter. If you are using
a telemetry-capable M-LINK receiver, the actual volt-
age of the receiver power supply will be displayed di-
rectly on the integral screen of your
ROYALevo
,
ROYAL SX
or
ROYAL SX
M-LINK
transmitter. If the
battery voltage falls below a certain threshold, the
transmitter also emits an audible signal to warn you
that the receiver battery is almost flat.
For more information on this feature, please refer to
the operating instructions supplied with your teleme-
try-capable M-LINK receiver.
10.4. Switching the transmitter on
with throttle-check active
Throttle-check is a safety function. If you are about to
fly a powered model, the throttle check (throttle lock)
prevents an electric motor bursting into life unexpec-
tedly if you switch the system on when the throttle
channel is not at idle.
You will find the parameter Check Thr. in the menu:
Setup, Transmitter:
¡Transmitter
¨Exit
Sound All
Safety
Check Thr. ON_
Check RF ON
The factory default setting is ON. The conditions for
throttle-check are different for fixed-wing model aircraft
and helicopters; for this reason they are described
separately in the next two sections.
10.4.1.
Throttle-check for fixed-wing models
This warning appears if:
Throttle-Check (Check Thr.) is set to ON (see above)
and
the throttle control is not in the idle position (or at
the motor OFF position)
and
Only these
buttons are
active!
Indicator for
throttle control
(throttle stick
in this case)
To Next Page
Loading...
