NAD C 390DD User Manual

USING THE AVR 4 REMOTE CONTROL
The AVR 4 remote control handset handles the key functions of the C 390DD. The AVR 4 can also be
used to directly command other NAD products that respond to applicable common remote control
codes. This includes other NAD Stereo Receiver, Integrated Amplier and Preamplier models. It has
additional controls to remotely operate NAD CD Players, AM/FM Tuners and dedicated AM/FM/DB
Tuners. It will operate up to a distance of 23ft (7m). Alkaline batteries are recommended for maximum
operating life. Two AA batteries should be tted in the battery compartment at the rear of the Remote
Control handset. When replacing batteries, check that they have been put in the right way round, as
indicated on the base of the battery compartment.
NOTE
The remote control handset supplied with the C 390DD is of a universal NAD type, designed to
operate several NAD models. Some buttons are applicable only to specic NAD models. Contact
your dealer or NAD audio specialist for assistance.
1 ON, OFF
The AVR 4 remote has a separate ON and OFF button.
ON: Switch C 390DD from Standby mode to operating mode.
OFF: Switch C 390DD to Standby mode.
NOTE
In order to turn ON the C 390DD from standby mode or back to standby mode, the rear panel
POWER switch must be in the ON position.
2 DEVICE SELECTOR
A Device Selector button determines only what component the AVR 4 will command; it does not
perform any function on the C 390DD.
• Press desired Device Selector button for the applicable buttons to be directed to a “page” of
commands relevant to the selected device. Upon selecting a Device, you can now press the
corresponding AVR 4 control buttons applicable for the selected Device.
3 INPUT SELECTORS
Refer to the corresponding labels printed in the remote control faceplate and their respective
assigned buttons to make use of these functions.
• Set the DEVICE SELECTOR to “AMP” in order to gain access to these buttons.
The following table illustrates the corresponding C390DD source input when one presses the
specied AVR 4 button.
AVR 4 BUTTON C390DD SOURCE INPUT
INPUT 1 Digital Coaxial 1
INPUT 2 Digital Coaxial 2
INPUT 3 Digital Optical 1
INPUT 4 Digital Optical 2
INPUT 5 Digital AES EBU
INPUT 6 Computer
INPUT 7 Digital USB Back
FRONT Digital USB Front
SOURCE 5/6
Toggle through the input sources including those from DD HDMI 1 and DD AP 1 modules
when installed.
4 NUMERIC KEYS
The numeric keys allow for direct input of tracks for CD players and direct channel/preset access for
tuners and receivers.
5 A/V PSET
In combination with the numeric keys, press a Preset number from 1 to 5 as referenced to A/V
Presets settings. Note that the Preset settings can be congured via the A/V Presets menu. This is not
applicable to C 390DD.
IDENTIFICATION OF CONTROLS
AVR 4 REMOTE CONTROL
2
10
11
12
1
3, 4
8
15
14
5
13
16
7
6
9
10
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

NAD C 390DD Specifications

General

Damping factor	800
Amplifier class	A
Frequency range	20 - 96000 Hz
Audio output channels	- channels
Peak power per channel	- W
Signal-to-Noise Ratio (SNR)	124 dB
Total Harmonic Distortion (THD)	0.005 %
Dynamic power per channel (4 Ohm)	350 W
Dynamic power per channel (8 Ohm)	160 W
RMS power output per channel (4 Ohm)	150 W
AC (power) in	Yes
USB 2.0 ports quantity	3
Digital audio optical in	2
Digital audio optical out	1
Speakers connectivity type	Banana connector
Purpose	Home
Product color	Black
Volume control	Rotary
Connectivity technology	Wired
Sustainability certificates	RoHS, ENERGY STAR
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.5 W
Power consumption (typical)	40 W
Certification	CE, TUV

Weight and Dimensions

Depth	388 mm
Width	435 mm
Height	132 mm
Weight	7700 g