EasyManuals Logo

NAD C 390DD User Manual

NAD C 390DD
24 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #13 background imageLoading...
Page #13 background image
LIBRARY
The AVR 4 can store a dierent library of default NAD codes for each of its
DEVICE SELECTOR “pages. If the original default library does not control
your NAD Blu-ray disc player or other components, follow the procedure
below to change the library code. Refer as well to the table below for a list
of applicable NAD Library Codes with their corresponding NAD models.
LOAD ANOTHER LIBRARY CODE
Example: Load NAD DVD Player T 517 library code to AVR 4’s “BD” device.
1 Press and hold [BD] in the DEVICE SELECTOR section of AVR 4.
2 While holding down the device button [BD], press “2” and “2” using AVR
4’s numeric buttons. “22” is the corresponding library code for T 517.
3 Press [ENTER] while still holding down the device button [BD]. The
BD device selector will ash once to indicate that the library input is
successful. Both the device selector button [BD] and [ENTER] can now
be released.
RESET THE AVR 4 TO ITS DEFAULT SETTINGS
The AVR 4 can be restored to its factory settings, including default libraries,
via the following procedures
1 Press and hold [ON] and [DELETE] buttons for about 10 seconds until
the AMP device button lights up.
2 Within two seconds of the AMP device button lighting up, release both
buttons. If the reset mode is successful, the [BD] device button will ash
twice.
TABLE OF LIBRARY CODES APPLICABLE TO AVR 4 REMOTE
CONTROL
LIBRARY CODE NAD PRODUCT DESCRIPTION
10 Default library for AMP” page
11 Zone 2
20 C 515BEE, C 545BEE, C 565BEE
21 T 535, T 585, M55; DVD section of L 54, VISO TWO, VISO FIVE
22 Default library for “BD” page; T 513, T 514, T 515, T 517
23 T 587, T 557, T 577, M56
30 IPD 1
31 IPD 2
40
Default library for “TUN” page; Tuner section of C 725BEE, T 175,
T737, T 747, T 755, T 765, T 775, T 785
41 C 422, C 425, C 426
42 C 445
NOTE
The AVR 4 may not necessarily contain all the control buttons applicable
for the above-mentioned NAD products. Use the prescribed remote
control of the specic NAD product for a full compliment of the
applicable remote control buttons.
IDENTIFICATION OF CONTROLS
AVR 4 REMOTE CONTROL
13
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Other manuals for NAD C 390DD

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NAD C 390DD and is the answer not in the manual?

NAD C 390DD Specifications

General IconGeneral
Damping factor800
Amplifier classA
Frequency range20 - 96000 Hz
Audio output channels- channels
Peak power per channel- W
Signal-to-Noise Ratio (SNR)124 dB
Total Harmonic Distortion (THD)0.005 %
Dynamic power per channel (4 Ohm)350 W
Dynamic power per channel (8 Ohm)160 W
RMS power output per channel (4 Ohm)150 W
AC (power) inYes
USB 2.0 ports quantity3
Digital audio optical in2
Digital audio optical out1
Speakers connectivity typeBanana connector
PurposeHome
Product colorBlack
Volume controlRotary
Connectivity technologyWired
Sustainability certificatesRoHS, ENERGY STAR
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (standby)0.5 W
Power consumption (typical)40 W
CertificationCE, TUV
Weight and Dimensions IconWeight and Dimensions
Depth388 mm
Width435 mm
Height132 mm
Weight7700 g

Related product manuals