Need help?Do you have a question about the Netgate SG-2100 and is the answer not in the manual?
General| Storage | 8 GB eMMC |
|---|---|
| Ethernet Ports | 5 x 1 GbE |
| USB Ports | 1 x USB 3.0 |
| Operating System | pfSense Plus |
| CPU | Quad Core ARM Cortex-A53 1.2 GHz |
| RAM | 2 GB |
| Power Supply | 12V DC |
| Console Port | 1 x RJ-45 (Serial) |
Describes the subsequent steps after initial connection and configuration of the firewall.
Steps to access the web interface and begin the firewall setup process.
A guided process for the initial configuration of the firewall software.
Configuring the time server settings for the firewall appliance.
Setting up the Wide Area Network (WAN) interface for internet connectivity.
Details on the default IP address and subnet mask for the LAN interface.
An overview of the pfSense Plus dashboard and its navigation elements.
Instructions on how to restart the initial setup wizard for the firewall.
Procedures for backing up and restoring firewall configurations.
Description of the rear panel of the Netgate 2100 and its various ports.
Details on the WAN combo-port and its associated LED indicators.
Information regarding the four LAN Ethernet ports and their switch functionality.
Listing and description of other ports like USB, Micro SIM, and serial console.
Description of the front panel of the Netgate 2100 and its status indicators.
Explanation of the LED indicators and their meanings during operation.
Important safety instructions and warnings for product usage.
Guidelines for safe electrical connections and operation of the device.
Statement of compliance regarding FCC rules and operational conditions.
Statement of conformity with relevant EU directives and essential requirements.
Information on dispute resolution procedures, including binding arbitration.
Details on the governing law and venue for terms of use and disputes.
Information regarding site policies, terms modification, and severability.
General provisions and clarifications for the terms and conditions of use.
Details on the product's warranty terms, disclaimers, and limitations of liability.
Guidance on how to mount the Netgate 2100 appliance to a wall.
Steps to install necessary drivers for console access via USB.
Instructions for physically connecting the device to a workstation using a USB cable.
How to power the device to enable console access.
Locating the correct serial port device on the workstation.
How to start and configure terminal emulation software for console access.
Specific settings required for terminal programs like PuTTY.
Common problems and solutions for establishing console connectivity.
A step-by-step guide for reinstalling the pfSense Plus software using the recovery image.
Instructions for installing an M.2 SATA drive into the Netgate appliance.
Steps to configure VLANs on the switch ports for network segmentation.
Assigning interfaces and configuring switch ports for specific network roles.
Prerequisites for configuring an additional WAN interface.
Steps to assign an OPT interface for use as a WAN connection.
Enabling and configuring the OPT interface settings for the WAN.
Setting up Network Address Translation (NAT) for the new WAN interface.
Configuring firewall rules to manage traffic for the additional WAN.
Creating gateway groups for failover and load balancing.
Setting up DNS servers for the new WAN interface.
Configuring policy routing to direct traffic through specific WANs.
Configuring dynamic DNS for WAN connectivity.
Notes on using VPNs and their considerations with multiple WAN connections.
Methods for testing the functionality and connectivity of the additional WAN.
Prerequisites for configuring an additional LAN interface.
Steps to assign an OPT interface for use as a LAN connection.
Enabling and configuring the OPT interface settings for the LAN.
Configuring the DHCP server to assign addresses for the new LAN.
Setting up Network Address Translation (NAT) for the new LAN subnet.
Configuring firewall rules for open and isolated LAN scenarios.
A step-by-step guide for performing a factory reset using the hardware button.
Description of how LAN ports connect to the internal switch.
Explanation of the default Port VLAN Mode for switch ports.
Information on enabling and configuring the 802.1q VLAN mode for switch ports.
Information on training courses offered by Netgate to enhance pfSense knowledge.
Links to the Netgate Resource Library for additional helpful resources.
Details on professional services offered by Netgate for complex tasks.
Information on accessing the Netgate community forum for peer support.
Details regarding the Netgate 2100's manufacturer's warranty.
Information on where to find support plans and additional documentation.
To Next Page
