NETGEAR D6200 User Manual

Troubleshooting
144
D6200 WiFi DSL Modem Router
• Some cable modem service providers require you to use the MAC address of the
computer initially registered on the account. You can view the MAC address in the
Attached Devices screen.
Troubleshoot with the LEDs
After you turn on power to the WiFi DSL modem router, the following sequence of events
should occur:
1. When
power is first applied, verify that the Power LED is lit.
2. V
erify that the Power LED turns red within a few seconds, indicating that the self-test is
running.
3. Af
ter approximately 30 seconds, verify the following:
• The Power
LED is solid green.
• The
Internet LED is lit.
• The Eth
ernet LED is lit for any local port that is connected to a computer. This LED
indicates that a link has been established to the connected device.
The LEDs on the front panel of the WiFi DSL modem route
r can be used for troubleshooting.
Power LED Is Off or Blinking
• Make sure that the power cord is securely connected to your WiFi DSL modem router and
that the power adapter is securely connected to a functioning power outlet.
• Make sure that
you are using the power adapter that NETGEAR supplied for this product.
• If the Po
wer LED blinks slowly and continuously, the WiFi DSL modem router firmware is
corrupted. This situation can happen if a firmware upgrade is interrupted, or if the WiFi
DSL modem router detects a problem with the firmware. If the error persists, you have a
hardware problem. For recovery instructions or help with a hardware problem, contact
technical support at http://support.netgear.com/general/contact/default.aspx.
Power LED Stays Red
When the WiFi DSL modem router is turned on, the Power LED turns red for about 20
seconds and then turns green. If the LED does not turn green, the WiFi DSL modem router
has a problem.
If the Power LED is still red 1 minute after you turn o
n power to the WiFi DSL modem router:
1. T
urn off the power and back on to see if the WiFi DSL modem router recovers.
2. Press and ho
ld the Reset button to return the WiFi DSL modem router to its factory
settings.
See Factory Settings on
page 153.

NETGEAR D6200 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Wi-Fi band	Dual-band (2.4 GHz / 5 GHz)
Wi-Fi standards	802.11a, Wi-Fi 5 (802.11ac), 802.11b, 802.11g, Wi-Fi 4 (802.11n)
Top Wi-Fi standard	Wi-Fi 5 (802.11ac)
WLAN data transfer rate (max)	867 Mbit/s
USB version	2.0
Rack mounting	No
USB ports quantity	1
WLAN data transfer rates supported	300, 867 Mbit/s
Ethernet LAN (RJ-45) ports	4
DHCP client	-
Security algorithms	WPA, WPA2-PSK, WPS
Product color	Black
Flash memory	128 MB
Certification	RoHS
Windows operating systems supported	Windows 2000, Windows 2000 Professional, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 8, Windows 8 Enterprise, Windows 8 Enterprise x64, Windows 8 Pro, Windows 8 Pro x64, Windows 8 x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Enterprise, Windows Vista Enterprise x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64
Cables included	LAN (RJ-45)

Weight and Dimensions

Depth	77 mm
Width	255 mm
Height	205 mm
Weight	654 g