EasyManuals Logo

NETGEAR WNDR4300 User Manual

NETGEAR WNDR4300
129 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #117 background imageLoading...
Page #117 background image
Troubleshooting
117
N750 Wireless Dual Band Gigabit Router WNDR4300
Wired and wirelessly connected computers need to have network (IP) addresses on the
same network as the router. The simplest way to do this is to configure each computer to
obtain an IP address automatically using DHCP.
Some cable modem service providers require you to use the MAC address of the
computer initially registered on the account.
You can view the MAC address in the
Attached Devices screen.
Troubleshoot with the LEDs
After you turn on power to the router, the following sequence of events should occur:
1. When power is first applied, verify that the Power LED
lights.
2. After 2 minutes, verify the following:
The Power LED lights solid green.
The Internet LED lights.
The 2.4 GHz and 5 GHz LEDs light.
The LEDs on the front panel of the router can be used for troubleshooting.
Power LED Is Off or Blinking
Make sure that the power cord is securely connected to your router and that the power
adapter is securely connected to a functioning power outlet.
Check that you are using the 12V DC, 5A power adapter that NETGEAR supplied for this
product.
If the Power LED blinks slowly and continuously
, the router firmware is corrupted. This can
happen if a firmware upgrade is interrupted, or if the router detects a problem with the
firmware. If the error persists, you have a hardware problem. For recovery instructions, or
help with a hardware problem, contact technical support at www.netgear.com/support.
LEDs Never Turn Off
When the router is turned on, the LEDs light for about 10 seconds and then turn off. If all the
LEDs stay on, there is a fault within the router.
If all LEDs are still lit 1 minute after power-up:
Cycle the power to see if the router recovers.
Press and hold the Restore Factory Settings button to return the router to its factory
settings as explained in Factory Settings on page 123.
If the error persists, you might have a hardware problem and should contact technical
support at www.netgear.com/support.

Table of Contents

Other manuals for NETGEAR WNDR4300

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR WNDR4300 and is the answer not in the manual?

NETGEAR WNDR4300 Specifications

General IconGeneral
Ethernet LANYes
Cabling technology10/100/1000Base-T(X)
Networking standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN interface typeGigabit Ethernet
Wi-Fi bandDual-band (2.4 GHz / 5 GHz)
Wi-Fi standards802.11a, 802.11b, 802.11g
Top Wi-Fi standardWi-Fi 4 (802.11n)
WLAN data transfer rate (max)450 Mbit/s
Bandwidth2.4 GHz
Rack mounting-
xDSL connectionNo
Dimensions (WxDxH)218 x 160 x 35 mm
USB ports quantity1
Minimum system requirements- Internet Explorer 5.0, Firefox 2.0, Safari 1.4, Google Chrome 11.0
WLAN data transfer rates supported300, 450 Mbit/s
Ethernet LAN (RJ-45) ports5
Supported network protocolsIPv6
Security algorithmsWPA-PSK, WPA2-PSK
Flash memory128 MB
Certification- RoHS
Product colorBlack
Cables includedLAN (RJ-45)
Windows operating systems supportedWindows 2000, Windows 2000 Professional, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Professional
Weight and Dimensions IconWeight and Dimensions
Depth160 mm
Width218 mm
Height35 mm
Weight450 g

Related product manuals