OHAUS Explorer EX225D

To Next Page

To Previous Page

EN-144 EXPLORER BALANCES

Figure 9-4. EX12001, EX24001 and EX35001 models

14.8 in.

377 mm

4.7 in.

120 mm

17.4 in.

443 mm

12.1 in.

1.9 in.

48 mm

311 mm

w ww . . co m

information@itm.com1.800.561.8187

Main Page

Table of Contents3
Introduction7
Description7
Features7
Safety Precautions8
Installation9
Unpacking9
Terminal Setup10
Installing the Wind Ring, Weighing Platform on Semi-Micro Models10
Installing the Wind Ring, Weighing Platform on Models EX12410
Installing the Glass Shelf (on Semi-Micro Models)12
Installing the Weighing Pan & Wind Shield - Non-Draft Shield Models12
Selecting the Location13
Leveling the Equipment13
Connecting Power13
Models with AC Adapter13
Models with AC Power Cord14
Power on Button on EX12001, EX24001 and EX3500114
Connecting the Interface14
Adjusting the View Angle of the Terminal14
Remote Terminal Operation15
Separating the Terminal from the Weighing Base15
Terminal Mounting15
Initial Calibration16
Operation17
Overview of Display, Home Screen17
Principal Functions and Main Menu17
Overview of Parts and Features18
Overview of Parts and Features -Draft Shield Models19
Overview of Parts and Features - Non-Draft Shield Models20
Overview of Parts and Features - EX12001, EX24001 and EX3500121
Overview of Parts and Features - Terminal22
Functions and Their Icons23
Standby23
Printing Data23
Zero Operation23
Touchless Sensor Status23
Autocal23
Menu23
More23
Level Assist23
Graduations24
Routine Test24
Applications24
Taring a Container24
Weighing Units24
Ionizer (Only for EX225D/AD and EX225/AD)24
Preset Tare24
Calibration Test24
Calculator24
Stopwatch25
Logout25
Ionizer (EX225D/AD and EX225/AD Only) and Glass Shelf25
Application26
Weighing27
Edit Settings27
Application Setup29
Save to USB30
Auto Save to USB30
Statistics for Weighing30
Parts Counting32
Standard Parts Counting (Default)32
Application Setup35
Parts Counting - Check36
Parts Counting - Fill37
Statistics for Parts Counting38
Percent Weighing40
Edit Settings40
Application Setup42
Check Weighing43
Standard Check Weighing (Default)43
Edit Settings43
Application Setup44
Check Weighing - Nominal/Weight Tolerance Mode45
Check Weighing - Nominal/Percent Tolerance Mode46
Display Settings47
Statistics for Check Weighing48
Dynamic/Animal Weighing49
Edit Settings50
Application Setup50
Dynamic Weighing - Semi-Auto51
Dynamic Weighing - Automatic52
Statistics for Dynamic Weighing53
Filling54
Edit Settings54
Application Setup55
Statistics for Filling56
Totalization58
Totalization - Manual (Default)58
Application Setup59
Totalization - Automatic60
Formulation61
Free Formulation (Default)61
Application Setup62
Recipe Formulation63
Differential Weighing66
Item Settings66
Application Setup68
Differential Weighing with Auto-Process on69
Density Determination70
Measuring the Density of a Solid Using Water (Default)70
Application Setup72
Measuring the Density of a Buoyant Material Using Water73
Measuring the Density of a Solid Using an Auxiliary Liquid73
Measuring the Density of a Liquid Using a Calibrated Sinker (Not Supplied)74
Measuring the Density of Porous Material Using Oil76
Peak Hold78
Peak Hold - Semi-Automatic (Default)78
Application Setup79
Peak Hold - Manual80
Peak Hold - Automatic81
Ingredient Costing (Not Available in Semi-Micro Models)82
Item Settings82
Application Setup85
Pipette Adjustment (Not Available in EX12001, EX24001, EX35001)86
Pipette Adjustment - Manual (Default)86
Begin Pipette Adjustment Process88
Application Setup89
Statistical Quality Control (SQC)90
Edit Settings90
Begin the SQC Process91
Application Setup92
Fill Weight Variation94
Edit Settings94
Begin the Fill Weight Variation Process96
Application Setup97
Statistics97
Library98
Creating a Library Record98
Retrieving a Library Record99
Deleting a Stored Library Record99
Additional Features99
Weigh below99
Menu Settings100
Menu Navigation100
Changing Settings100
Main Menu100
Calibration101
Calibration Sub-Menu101
Internal Calibration (Autocal™)101
Automatic Calibration101
Auto TM Interval (Hours)102
Autocal™ Adjustment102
Span Calibration102
User Calibration103
Calibration Test103
User Management104
User Settings106
User Settings Sub-Menu106
Change Password106
Language106
Volume106
Display Settings106
Functions Configuration107
Touchless Sensor Setup107
Draft Shield Light107
Ionizer (Seconds)107
Balance Setup108
Balance Set-Up Sub-Menu108
Stable Range108
Filter Level108
Auto Zero Tracking108
Audible Signal108
Auto Tare109
Gross Indicator109
Legal for Trade109
Graduations109
Date & Time110
Applications111
Turning an Application ON/OFF111
Weighing Units111
Units Sub-Menu111
Turning a Unit ON/OFF112
Custom Units112
GLP and GMP Data113
GLP Data Sub-Menu113
Header113
Balance Name113
Project Name113
Communication114
Communication Sub-Menu114
Baud Rate114
Transmission114
Handshake115
Alternate Command115
Print Output115
Auto Print115
Print Calibration Data116
Print Content116
Print Layout119
Data Transfer Function119
Library120
Diagnostics120
Routine Test120
Level Bubble Light (Not Available in EX12001, EX24001, EX35001)121
Draft Shield Light (Analytical Models)121
Sensors121
Automatic Draftshield Door121
Data Maintenance121
Service Mode121
Factory Reset122
Factory Reset Sub-Menu122
Reset Calibration122
Reset User Settings122
Reset Balance Setup122
Reset Application Modes122
Reset Weighing Units122
Reset GLP and GMP Data122
Reset Communication122
Reset All (Global Reset)122
Information123
Using Information123
Legal for Trade124
Settings124
Verification124
Sealing124
Printing125
Connecting, Configuring and Testing the Printer/Computer Interface125
Printout Examples126
Output Format136
Maintenance137
Calibration137
Cleaning137
Troubleshooting137
Service Information137
Technical Data138
Specifications138
Drawings and Dimensions145
Parts and Accessories147
Icons List148
Communication153
Interface Commands153
RS232 (DB9) Pin Connections156
The USB Interface156
Software Updates159
Compliance160

OHAUS Explorer EX225D - Page 146

Table of Contents

Other manuals for OHAUS Explorer EX225D

Related product manuals