Need help?Do you have a question about the Olympus UFL-2 and is the answer not in the manual?
General| Brand | Olympus |
|---|---|
| Model | UFL-2 |
| Category | Camera Flash |
| Language | English |
Essential instructions and safety warnings to be read before operating the product.
Safety notices specific to European, US, and Canadian regulations.
High-priority safety alerts regarding electrical hazards and unsafe environments.
Precautions against vision impairment and child safety when using the flash.
Guidelines for safe handling, especially concerning water and electrical risks.
Critical warnings about battery misuse, short circuits, and storage.
Instructions for keeping batteries dry and avoiding wet hand contact.
Information on incompatible batteries and correct insertion methods.
Procedures for handling battery leaks and temperature-related safety.
Essential points for maintaining the O-ring's condition and waterproof seal.
Warnings about using or storing the product in specific environmental conditions.
Guidelines to avoid damage from environment and excessive physical force.
List of chemicals that should not be used for cleaning to prevent product damage.
Identification of the primary parts of the electronic flash unit.
Steps to check all items are present in the product package.
Labeled illustration showing the location and names of flash components.
Explains the function of each numbered part of the flash unit shown in diagrams.
Explains the various indicators and information displayed on the control panel.
Notes on how panel displays may vary and relate to manual content.
Step-by-step guide for safely removing the O-ring from the flash unit.
Procedures for removing sand, dirt, and fibers from the O-ring and its groove.
Warnings against damaging the O-ring or using incorrect cleaning agents.
Instructions for applying the specified silicone grease to the O-ring.
Steps for correctly installing the O-ring into its groove for a proper seal.
Lists the compatible battery types for the electronic flash.
Detailed steps for inserting batteries correctly into the flash.
Cautions during battery installation, removal, and securing the battery cap.
Instructions for securely mounting the flash onto an accessory arm.
Guide to connecting the flash to an underwater camera case via fiber optic cable.
Instructions for connecting the flash using TTL cables and optional hot shoe accessories.
Steps to turn on the electronic flash and check its operational readiness.
Basic shooting guide when the flash is connected via a fiber optic cable.
How to use TTL AUTO mode for automatic flash intensity control.
How to change flash control modes like TTL AUTO, AUTO, and MANUAL.
Information on when certain flash modes might not be available.
Steps to enter and configure custom settings on the flash.
Options for customizing AF illuminator and flash cable behavior.
Settings for controlling zoom angle display and distance units.
Adjusting flash intensity and managing the wide-angle flash indicator.
Settings for how the guide number is displayed.
How to set ISO sensitivity and aperture values for flash.
Instructions to restore all custom settings to factory defaults.
Guide to configuring the flash to operate as a slave unit.
Important warnings for slave mode operation, including pre-flash interference.
Procedures for wiping away water from the flash unit.
Steps for safely removing batteries and resealing the unit.
Instructions for cleaning the flash, especially after saltwater use.
Methods for properly drying the flash unit after cleaning.
Guidelines for O-ring upkeep and recommended replacement schedule.
Important points to consider when removing and replacing the battery cap.
Risks associated with using or storing the flash in certain locations.
Procedures for handling the flash after use, including cleaning and drying.
Main causes leading to water ingress into the flash unit.
Key advice for effective O-ring care to maintain waterproofing.
Essential points for flash cleaning, corrosion prevention, and repairs.
Guidance on seeking professional repairs and warranty implications.
Details on available accessories like O-rings and specialized grease.
Explanation of the warning for being outside the light control range in AUTO mode.
Warning indicating the subject is too close in MANUAL mode.
Warning for subjects being too close when using FP MANUAL mode.
How to confirm test flash activation, auto-checking, and RC mode function.
Issues with flash control mode changes, AF illuminator, and light control range display.
Advice on optimal white balance settings for flash use.
How to check camera compatibility for wireless flash features.
Flash behavior when connected via TTL cable and the camera enters sleep mode.
Explains why the flash unit may automatically turn off.
To Next Page
