PLATINUM
TM
Series User’s Guide
5.3.6 Alarm High High / Low Low Offset Value (PRoG > ALM.1, ALM.2 > HI.HI) ......................... 38
5.3.7 Alarm Latching (PRoG > ALM.1, ALM.2 > LtCH) .................................................................. 38
5.3.8 Alarm Normally Closed, Normally Open (PRoG > ALM.1, ALM.2 > CtCL) ........................... 39
5.3.9 Alarm Power-On Behavior (PRoG > ALM.1, ALM.2 > A.P.oN) ............................................. 39
5.3.10 Alarm On Delay (PRoG > ALM.1, ALM.2 > dE.oN) ............................................................... 39
5.3.11 Alarm Off Delay (PRoG > ALM.1, ALM.2 > dE.oF) ............................................................... 39
5.4 Output Channel 1–3 Configuration (PRoG > oUt.1–oUt.3) ......................................................... 40
5.4.1 Output Channel Mode (PRoG > oUt1–oUt3 > ModE) ......................................................... 40
5.4.2 Output Cycle Pulse Width (PRoG > oUt1–oUt3 > CyCL) ...................................................... 42
5.4.3 Analog Output Range (PRoG > oUt1–oUt3 > RNGE) ........................................................... 43
5.5 PID Configuration (PRoG > PId.S) ................................................................................................ 43
5.5.1 Action Response (PRoG > PId > ACtN) ................................................................................ 43
5.5.2 Autotune Timeout (PRoG > PId > A.to) ............................................................................... 44
5.5.3 Autotune (PRoG > PId > AUto) ............................................................................................ 44
5.5.4 PID Gain Settings (PRoG > PId > GAIN) ................................................................................ 44
5.5.5 Low Output Clamping Limit (PRoG > PId > %Lo) ................................................................. 45
5.5.6 High Output Clamping Limit (PRoG > PId > %HI) ................................................................ 45
5.5.7 Adaptive Tuning (PRoG > PId > AdPt) ................................................................................. 45
5.6 Remote Setpoint Configuration (PRoG > RM.SP) ........................................................................ 46
5.6.1 Cascade Control using Remote Setpoint ............................................................................. 47
5.7 Multi-Ramp/Soak Mode Parameters (PRoG > M.RMP) .............................................................. 48
5.7.1 Multi-Ramp/Soak Mode Control (PRoG > M.RMP > R.CtL) ................................................. 48
5.7.2 Select Program (PRoG > M.RMP > S.PRG) ........................................................................... 49
5.7.3 Multi-Ramp/Soak Tracking (PRoG > M.RMP > M.tRk) ........................................................ 49
5.7.4 Time Format (PRoG > M.RMP > tIM.F) ............................................................................... 49
5.7.5 Program End Action (PRoG > M.RMP > E.ACT) ................................................................... 49
5.7.6 Number of Segments (PRoG > M.RMP > N.SEG) ................................................................. 50
5.7.7 Segment Number for Editing (PRoG > M.RMP > S.SEG) ..................................................... 50
5.7.8 More on Multi-Ramp/Soak Programming .......................................................................... 51
6. Reference Section: Operating Mode (oPER) ....................................................................................... 52
6.1 Normal Run Mode (oPER > RUN) ................................................................................................ 52
6.2 Change Setpoint 1 (oPER > SP1) .................................................................................................. 53
Omega Engineering | www.omega.com
To Next Page
Loading...
