Omron CJ2H-CPU6*-EIP Series User Manual

32
CJ2M CPU Unit Pulse I/O Module User’s Manual
CS/CJ/CP/NSJ-
series Communica-
tions Command Ref-
erence Manual
W342 CJ2H-CPU6@-EIP
CJ2H-CPU6@
CJ2M-CPU@@
CS1G/H-CPU@@H
CS1G/H-CPU@@-V1
CS1D-CPU@@H
CS1D-CPU@@S
CS1W-SCU@@-V1
CS1W-SCB@@-V1
CJ1H-CPU@@H-R
CJ1G/H-CPU@@H
CJ1G-CPU@@P
CJ1M-CPU@@
CJ1G-CPU@@
CJ1W-SCU@@-V1
CP1H-X@@@@-@
CP1H-XA@@@@-@
CP1H-Y@@@@-@
CP1L-M/L@@@-@
CP1E-E@@D@-@
CP1E-N@@D@-@
CP1L-M/L@@@-@@
CP1E-E/N@@D@-@
NSJ@-@@@@(B)-G5D
NSJ@-@@@@(B)-M3D
Information on communi-
cations for CS/CJ/CP-
series CPU Units and NSJ-
series Controllers
Describes C-mode commands and FINS com-
mands
Refer to this manual for a detailed description of
commands for communications with the CPU
Unit using C mode commands or FINS com-
mands.
Note This manual describes the communica-
tions commands that are addressed to
CPU Units. The communications path that
is used is not relevant and can include any
of the following: serial ports on CPU Units,
communications ports on Serial Commu-
nications Units/Boards, and Communica-
tions Units. For communications
commands addressed to Special I/O Units
or CPU Bus Units, refer to the operation
manual for the related Unit.
CX-One Setup Man-
ual
W463 CXONE-AL@@C-
V@/AL@@D-V@
Installing software from the
CX-One
Provides an overview of the CX-One FA Inte-
grated Tool Package and describes the installa-
tion procedure.
CX-Programmer
Operation Manual
W446 WS02-CX@@-V@ Support Software for Win-
dows computers
CX-Programmer operating
procedure
Describes operating procedures for the CX-Pro-
grammer.
Also refer to the Software User’s Manual (W473)
and CS/CJ/NSJ-series Instructions Reference
Manual (W474) when you do programming.
CX-Programmer
Operation Manual
Functions
Blocks/Structured
Tex t
W447
CX-Programmer
Operation Manual
SFC Programming
W469
CS/CJ/CP/NSJ-
series CX-Simulator
Operation Manual
W366 WS02-SIMC1-E Operating procedures for
CX-Simulator Simulation
Support Software for Win-
dows computers
Using simulation in the CX-
Programmer with CX-Pro-
grammer version 6.1 or
higher
Describes the operating procedures for the CX-
Simulator.
When you do simulation, also refer to the CX-
Programmer Operation Manual (W446), Soft-
ware User’s Manual (W473), and CS/CJ/NSJ-
series Instructions Reference Manual (W474).
CS/CJ/CP/NSJ-
series CX-Integrator
Network Configura-
tion Software Opera-
tion Manual
W464 CXONE-AL@@C-V@/
CXONE-AL@@D-V@
Network setup and moni-
toring
Describes the operating procedures for the CX-
Integrator.
Manual Cat. No. Model Application Description

Omron CJ2H-CPU6*-EIP Series Specifications

General

Brand	Omron
Model	CJ2H-CPU6*-EIP Series
Category	Controller
Language	English