Omron CP1E-E14SDR-A - Page 271

Index-2
CP1E CPU Unit Hardware User’s Manual(W479)
Wiring ....................................................................A-27
External power supply capacity.......................... 2-15, 2-17
F
Fail-safe circuits............................................................. 5-2
FAL error .............................................................. 6-6, 6-12
FALS error............................................................ 6-5, 6-10
Fatal errors
Cycle time exceeded error.............................. 6-5, 6-10
FALS error ...................................................... 6-5, 6-10
I/O bus error...................................................... 6-5, 6-8
Memory error.................................................... 6-5, 6-8
Program error ................................................... 6-5, 6-9
Too many I/O points error ................................. 6-5, 6-8
G
Grounding........................................................... 5-15, 5-16
H
High-speed counter..................................................... 3-13
I
I/O bus error ........................................................... 6-5, 6-8
I/O Connecting Cable.................................................. 2-10
I/O wiring..................................................................... 5-17
Indicator.................................................................. 3-4, 3-9
Checking errors ....................................................... 6-2
Communications errors.......................................... 6-14
CPU errors............................................................. 6-11
Errors....................................................................... 6-5
Fatal errors .............................................................. 6-7
Non-fatal errors...................................................... 6-12
Inductive loads ............................................................ 5-21
Input errors.................................................................. 6-15
Inspection and maintenance ......................................... 7-3
Installation and Wiring Products
Models................................................................... 2-10
Installation height .......................................................... 5-8
Installing the software.................................................... 4-7
Installing the USB Driver ............................................... 4-9
Interrupt inputs ............................................................ 3-13
L
Low Voltage Directive.................................................... -24
M
Maximum number of I/O Points.......................... 1-10, 2-12
Memory error.......................................................... 6-5, 6-8
Modbus-RTU Easy Master function............................. A-36
Model numbers.............................................................. 2-4
Models
CPU Unit.................................................................. 2-4
Expansion I/O Unit................................................. 2-13
Expansion Unit ...................................................... 2-14
Installation and Wiring Products............................ 2-10
Optional Products.................................................... 2-9
Mounting hole pitch..................................................... 5-10
N
N/NA-type CPU Unit...................................................... 1-2
Basic system configuration...................................... 2-3
E10/14/20 or N14/20 CPU Units.............................. 3-2
E30/40, N30/40/60 or NA20 CPU Units................... 3-7
Models..................................................................... 2-8
Noise control ............................................................... 5-21
External wiring..............................................5-22, A-48
Relay output........................................................... 5-22
Non-fatal errors
Backup memory error..................................... 6-6, 6-12
Battery error.................................................... 6-6, 6-13
FAL error......................................................... 6-6, 6-12
Option Board error.......................................... 6-6, 6-13
PLC Setup error..............................................6-6, 6-13
No-protocol communications.......................................A-34
Normal inputs.............................................................. 3-13
Normal Outputs........................................................... 3-16
NT Link........................................................................A-33
Number of connected Units......................................... 5-13
Number of Expansion (I/O) Units
connected.......................................1-10, 2-12, 2-15,5-13
Number of simultaneously ON points.......................... 2-15
O
Operating environment.................................................. 4-4
Option Board ............................................................... 3-19
Option Board error................................................ 6-6, 6-13
Option Board slot........................................................... 3-8
Option Boards
Dimensions..............................................................A-5
Optional Products
Models..................................................................... 2-9
Output errors............................................................... 6-16
Output wiring............................................................... 5-20
P
Part names and functions
Analog I/O Unit ...................................................... 8-22
Analog Input Unit ..................................................... 8-2
Analog Output Unit ................................................ 8-12
CompoBus/S I/O Link Unit..................................... 8-52
E10/14/20 or N14/20 CPU Units.............................. 3-2
E30/40, N30/40/60 or NA20 CPU Units................... 3-7
Expansion I/O Unit................................................. 3-27
Expansion Input Unit.............................................. 3-24
Expansion Output Unit........................................... 3-25
Temperature Sensor Unit....................................... 8-36
Periodic inspection ........................................................ 7-2
Peripheral USB port ...............................3-3, 3-8, 4-8, 6-18
PLC Setup error ................................................... 6-6, 6-13
Power consumption....................................................... 1-9
Power supply error ........................................................ 6-5
Precautions
Precautions on Connecting Units .......................... 5-13
Precautions when connecting a two-wire
DC sensor........................................................... 5-19
Restrictions of CPU Unit with 16 or 32 I/O Points.. 3-30
Restrictions on system configuration..................... 2-15
Unit replacement precautions.................................. 7-4
Program capacity ............. 1-2, 1-10, 2-5, 2-6, 2-7, 2-8, 2-9
Program error......................................................... 6-5, 6-9
Programming devices.................................................... 4-2
Pulse outputs............................................................... 3-17
PWM output................................................................. 3-17
Q
Quick-response inputs................................................. 3-13