Omron CP1E-ED

Index-2
CP1E CPU Unit Hardware User’s Manual(W479)
Wiring .................................................................... A-24
External power supply capacity.......................... 2-13, 2-15
F
Fail-safe circuits............................................................. 5-2
FAL error .............................................................. 6-6, 6-12
FALS error............................................................ 6-5, 6-10
Fatal errors
Cycle time exceeded error.............................. 6-5, 6-10
FALS error ...................................................... 6-5, 6-10
I/O bus error...................................................... 6-5, 6-8
Memory error.................................................... 6-5, 6-8
Program error ................................................... 6-5, 6-9
Too many I/O points error ................................. 6-5, 6-8
G
Grounding........................................................... 5-15, 5-16
H
High-speed counter..................................................... 3-10
I
I/O bus error ........................................................... 6-5, 6-8
I/O Connecting Cable.................................................... 2-8
I/O wiring ..................................................................... 5-17
Indicator.................................................................. 3-3, 3-7
Checking errors ....................................................... 6-2
Communications errors.......................................... 6-14
CPU errors............................................................. 6-11
Errors....................................................................... 6-5
Fatal errors .............................................................. 6-7
Non-fatal errors...................................................... 6-12
Inductive loads ............................................................ 5-21
Input errors.................................................................. 6-15
Inspection and maintenance ......................................... 7-3
Installation and Wiring Products
Models..................................................................... 2-8
Installation height .......................................................... 5-7
Installing the software.................................................... 4-7
Installing the USB Driver ............................................... 4-9
Interrupt inputs ............................................................ 3-10
L
Low Voltage Directive ......................................................24
M
Maximum number of I/O Points.......................... 1-10, 2-10
Memory error.......................................................... 6-5, 6-8
Modbus-RTU Easy Master function............................. A-32
Model numbers.............................................................. 2-4
Models
CPU Unit.................................................................. 2-4
Expansion I/O Unit................................................. 2-11
Expansion Unit ...................................................... 2-12
Installation and Wiring Products.............................. 2-8
Optional Products.................................................... 2-7
Mounting hole pitch ..................................................... 5-10
N
N/NA-type CPU Unit...................................................... 1-2
Basic system configuration...................................... 2-3
E10/14/20 or N14/20 CPU Units.............................. 3-2
E30/40, N30/40/60 or NA20 CPU Units................... 3-6
Models..................................................................... 2-5
Noise control ............................................................... 5-21
External wiring ..............................................5-22, A-43
Relay output........................................................... 5-22
Non-fatal errors
Backup memory error..................................... 6-6, 6-12
Battery error.................................................... 6-6, 6-13
FAL error......................................................... 6-6, 6-12
Option Board error.......................................... 6-6, 6-13
PLC Setup error.............................................. 6-6, 6-13
No-protocol communications....................................... A-31
Normal inputs .............................................................. 3-10
Normal outputs............................................................ 3-13
NT Link........................................................................A-30
Number of connected Units......................................... 5-13
Number of Expansion (I/O)
Units connected.............................1-10, 2-10, 2-13, 5-13
Number of simultaneously ON points.......................... 2-13
O
Operating environment.................................................. 4-4
Option Board ............................................................... 3-16
Option Board error................................................ 6-6, 6-13
Option Board slot........................................................... 3-7
Option Boards
Dimensions..............................................................A-3
Optional Products
Models ..................................................................... 2-7
Output errors ............................................................... 6-16
Output wiring ............................................................... 5-20
P
Part names and functions
Analog I/O Unit ...................................................... 8-22
Analog Input Unit ..................................................... 8-2
Analog Output Unit ................................................ 8-12
CompoBus/S I/O Link Unit..................................... 8-52
E10/14/20 or N14/20 CPU Units.............................. 3-2
E30/40, N30/40/60 or NA20 CPU Units................... 3-6
Expansion I/O Unit................................................. 3-23
Expansion Input Unit.............................................. 3-20
Expansion Output Unit........................................... 3-21
Temperature Sensor Unit....................................... 8-36
Periodic inspection ........................................................ 7-2
Peripheral USB port ...............................3-2, 3-6, 4-8, 6-18
PLC Setup error ................................................... 6-6, 6-13
Power consumption ....................................................... 1-9
Power supply error ........................................................ 6-5
Precautions
Precautions on Connecting Units .......................... 5-13
Precautions when connecting
a two-wire DC sensor.......................................... 5-19
Restrictions of CPU Unit
with 16 or 32 I/O Points....................................... 3-26
Restrictions on system configuration..................... 2-13
Unit replacement precautions.................................. 7-4
Program capacity ............................1-2, 1-10, 2-4, 2-5, 2-6
Program error ......................................................... 6-5, 6-9
Programming devices.................................................... 4-2
Pulse outputs............................................................... 3-14
PWM output................................................................. 3-14
Q
Quick-response inputs................................................. 3-10
R
Rotary switch............................................................... 8-39